INSTRUCTIONS FOR USE
Please read and keep these instructions
advanced electric steriliser and dryer
423242
09140619_1
Do not touch hot surfaces use handles and knobs.
When in use the Steriliser and Dryer contains hot water and
steam. Keep hands away from steam vents as it can cause
burns and scalds. Use in a well ventilated area.
Do not operate any appliance with a damaged cord, plug or
after the appliance malfunctions or has been damaged in any
manner. If the supply cord is damaged it must be changed by
a qualified person in order to avoid a hazard.
Always use on a flat heat resistant surface.
Do not move appliance when in use.
Do not let the cord hang over edge of kitchen work surface or
touch hot surfaces.
Do not use any accessories other than those supplied with
this appliance.
IMPORTANT WARNINGS!
These instructions can also be found at
www.tommeetippee.com
Keep this instruction leaflet for future reference as it
includes important information.
This appliance is intended for household use only.
Do not use outdoors.
Before plugging in the Steriliser and Dryer for the first time
ensure that the voltage is compatible with your electricity
supply by checking the label on the base of the unit.
Ensure water has been added to the unit before switching the
unit on.
Do not immerse in water, to protect against fire, electric shock
and injury to persons. Do not immerse cord, plugs or other
parts of the unit in water or other liquid.
Misuse of the product may result in the risk of fire, electric
shock and/or personal injury.
This appliance shall not be used by children. Keep the
appliance and its cord out of reach of children.
Appliances can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand
the hazards involved.
Children shall not play with the appliance.
User maintenance other than cleaning and descaling is not
required for this product. Cleaning and user maintenance
shall not be made by children.
The heating element surface is subject to residual heat
after use.
May
bor
n (UK
) Lim
ite
d,
Ball
iol
Bus
ines
s P
ark
,
New
cas
tle u
pon T
yne
,
NE1
2 8
EW, UK
Cop
yrig
ht © M
ayb
orn (
UK) L
im
ite
d 201
9.
Mad
e in
China
.
Mod
el n
um
ber
: WX-
965
D. V
olta
ge: A
C22
0-2
40V
~ 50-
60H
z 600
W
Any
ques
tion
s?
Visi
t o
ur w
ebsite
tom
meet
ipp
ee.
com
PARTS GUIDE
a
b
c
e
INFORMATION ON THE DISPOSAL FOR WASTE ELECTRICAL & ELECTRONIC EQUIPMENT (WEEE)
This symbol on the products and accompanying documents means that used electrical and electronic products should not be
mixed with general household waste. For proper disposal for treatment, recovery and recycling, please take these products to
designated collection points where they will be accepted on a free of charge basis. In some countries you may be able to return
your products to your local retailer upon the purchase of a new product.
Disposing of this product correctly will help you save valuable resources and prevent any possible effects on human health and
the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further
details of your nearest collection point for WEEE.
Penalties may be applicable for the incorrect disposal of this product in accordance with national legislation.
The product is fitted with a mains plug containing a fuse (10A). If it ever becomes necessary to replace the fuse, only use fuses
that are marked AC250V, and rated at 10A. In the unlikely event that this plug is not suitable for the sockets in your home, it
should be removed and a suitable plug fitted as follows:
The wires of the mains lead are coloured in accordance with the following code:
GREEN AND YELLOW – EARTH
BLUE – NEUTRAL
BROWN – LIVE
As these colours may not correspond with the coloured markings sometimes used to identify the terminals in
the plug, connect as follows.
The wire coloured GREEN AND YELLOW must be connected to the terminal marked E or by the earth symbol
or coloured GREEN or GREEN AND YELLOW. The wire coloured BLUE must be connected to the terminal
marked N or coloured BLACK. The wire coloured BROWN must be connected to the terminal marked L or
coloured RED.
If you are in any doubt about how to wire a plug or replace a fuse safely, consult a qualified electrician.
STERILISE AND DRY
1. Press the Automatic sterilise and dry button once. The appliance will beep once and the sterilisation cycle
will start. The sterilising time is approximately 10 minutes.
2. When the sterilising cycle is complete, the drying cycle will follow automatically.
The drying time is approximately 30 minutes.
3. When the drying cycle is complete, the appliance will beep 5 times and power off automatically. Please allow to
cool for at least 5 minutes before opening the steriliser.
STERILISE ONLY
1. Press the sterilise button once. The appliance will beep once and the sterilisation cycle will start. The sterilising
time is approximately 10 mins.
2. When sterilisation cycle is complete, the appliance will beep 5 times and switch off automatically. Please allow
to cool for at least 5 minutes before opening the steriliser.
CAUTION!
If you need to drain water from the base, always pour sideways away from the air vent in the direction marked inside
the base.
DRY ONLY
1. Press the dry button once. The appliance will beep once and the drying cycle will start.
2. The drying cycle is approximately 30 minutes.
3. When the drying cycle is completed, the appliance will beep 5 times and switch off automatically. Please allow
to cool for at least 5 minutes before opening the steriliser.
Please note: The sterilisation and/or the drying cycle can be stopped any time by pressing the on/off button.
CLEANING
Unplug and allow to cool before cleaning. After each use pour away remaining water from the steriliser base by tipping
the steriliser and dryer sideways over a sink, ensuring no water gets into the air vent (i), and wipe clean with a damp
cloth only. The lid (a) and the two racks (b, c) can be cleaned in hot water. Do not clean with abrasive cleaners.
d
f
HOW TO REPLACE THE FILTER
a. Lid
b. Upper rack
c. Lower rack
d. Steriliser base
e. Control panel
f. Lead with plug
g. Stainless steel heater surface
h Max fill line
i. Air vent
It is recommended to change the filter every 6 months.
The filter is found on the underside of the steriliser base (j).
To change the filter:
1. Unclip the filter panel door (k) and remove old filter.
2. Place the filter (l) into the steriliser base,
making sure that the tab handle is still visible on top of the filter (m).
3. Place the filter panel door back onto the steriliser base (j).
k
l
d
CONTROL PANEL
On/ off
Sterilise
Dry
Automatic
sterilise
and dry
BEFORE FIRST USE
You must insert the filter provided into the underside of the steriliser base before you start using the steriliser and dryer.
USAGE
It is important that all bottles, teats and accessories are empty and that they are clean and fully rinsed in fresh
water before placing in the appliance for sterilisation.
Use on level surface and be sure there is no debris under the unit and the rubber pads are touching the surface.
This steriliser is designed for use with Tommee Tippee bottles and feeding accessories (except bottle brush).
The steriliser will hold a maximum of 6 Tommee Tippee Closer to Nature bottles (maximum 4 Advanced Anti-colic bottles)
or a combination of fewer bottles plus soothers and breast pump parts.
Plug the steriliser into the power outlet.
Press the on/off button.
The steriliser will emit a “beep”
sound and the button will light up.
Choose your desired function
following the instructions on the
next page.
Place the lid (a) on top.
Please ensure that the lid fits
securely onto the upper rack
without any gaps.
4
5
WARNING!
TO AVOID THE RISK OF ELECTRIC SHOCK, INJURY OR DAMAGE: ALWAYS UNPLUG YOUR PRODUCT BEFORE
CLEANING. DO NOT IMMERSE THE BASE, THE SUPPLY CORD OR THE PLUG IN WATER OR OTHER LIQUIDS.
DO NOT CLEAN BASE UNDER WATER TAP.
DO NOT use metal objects or scourers to clean your Steriliser and Dryer. DO NOT use bleach or sterilising fluid to
clean it. DO NOT use abrasive or anti-bacterial materials. DO NOT scrub the heat plate.
CAUTION! UNDER NO CIRCUMSTANCES USE ABRASIVE, CORROSIVE OR SCRATCHING CLEANING AGENTS,
AS THESE COULD DAMAGE YOUR STERILISER.
Please note: If there is insufficient water to complete the sterilisation phase effectively, the appliance will ‘”beep” 5
times and the function light will flash for 2 hours. Do not use the bottles or accessories. Repeat usage instructions
to ensure effective sterilisation. Drying time based on 260ml / 9oz bottles. If you are using larger bottles, then extra
drying time may be required.
DE-SCALING
The guide below shows what the frequency of de-scaling should be.
Hard water: 14 days
Medium: 21 days
Soft: 28 days
You can find out your water quality from your water provider.
Unplug the unit and allow to cool before descaling. After each use pour away remaining water from the unit base by
tipping the unit sideways over a sink and wipe with a damp cloth only. We recommend that you descale your appliance
according to the guidelines above to ensure that it continues to work efficiently. Living in a hard water area can
produce limescale quicker than other areas so descaling is required sooner. Use a descaler that is suitable for use
with stainless steel and use as per the manufacturer’s guidelines. Or you can use white vinegar or a descaling sachet
to descale your unit. Please use as per manufacturer’s guidelines. Where no method is stated, 1:4 descaler to water
ratio can be applied.
TROUBLE SHOOTING
This information can also be found at tommeetippee.com
CONDITION
POSSIBLE CAUSE
REMEDY
Machine will not start
Appliance is unplugged
Make sure the plug is securely
inserted into the power outlet and
power is turned on
Appliance is not turned on
Press on/ off button before
choosing function
Scaling on the stainless
steel heater surface
Limescale
Descale Unit
White marks on bottles
Limescale
Descale Unit
AUTO
j. Steriliser base (underside)
k. Filter panel door
l. Filter
m. Filter tab handle
j
g
m
CHOOSE YOUR FUNCTION
Remove the lid (a) and the racks (b),
(c) from the steriliser base (d). Pour
120ml of water onto the stainless
steel heater surface (do not go over
the max fill line (h)). If using dry only
function you do not need to add
any water.
Insert lower rack (c), place clean
bottles with their opening facing
downward onto the lower posts.
Place hoods onto the bottle bases.
1
AUTO
Insert the upper rack (b) and
place in the bottle accessories
(eg. teat and screw ring).
2
AUTO
3
h
i
4
AUTO
