Tomar TRX-20 Product Manual Download Page 5

IS0615-02 

 

Page 

5

 of 

9

 

 

Mounting 

 

TRX lightbars include L shape mounting brackets designed to secure the lightbar  to a flat surface. The 
bracket  will  allow  a  135°  range  of  motion.  For  additional  mounting  options  visit 

www.tomaroff-

road.com

.  

 

1.

 

Attach the mounting foot to the lightbar using the 

1/4 -20

 socket head screws and ¼” flat 

washers included with the lightbar, leaving the screws finger tight.  

2.

 

Place  the  lightbar  with  attached  mounting  feet  on  a  flat  surface  that  has  sufficient 
strength to support  its weight. Using the holes in the  mounting brackets as a template 
mark the location of the mounting holes. The mounting holes in the bracket are designed 
to  free  fit  ¼  inch  hardware.  Recommended  drill  sizes  for  ¼”  hardware  are 

17/64

”  for 

clearance holes  and 

13/64

 for tapped holes. Note: the  hole  pattern on the foot is on 2” 

centers. For the hole spacing between the mounting feet refer to the Dimensions section 
below.  

3.

 

Once the lightbar is secured to the mounting surface, adjust the lightbar to the desired 
angle and tighten the ¼-

20

 socket head screws to approx. 36 in/lb.  

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for TRX-20










Reviews: