background image

 

 

 
 

Page 8

 

 

 

 

 

 

This symbol means that the guards must remain in place while the engine/motor on the machine is 
running because death or personal injury may result.

 

(Yellow background with black pictogram and black outline)

 

 

 

This symbol means that there are moving parts and if feet/fingers/digits are inserted under any edge of 
the cutter/grinder/saw cover while the engine/motor on the machine is running that personal injury and loss 
of foot/fingers/digits may result.

 

(Yellow background with black pictogram and black outline)

 

 
 

This symbol means the surface is HOT and that if fingers/digits/hands or any bare or unprotected skin comes 
in contact with this surface or hot accessory, possible serious burns and personal injury may result. (Yellow 
background with black pictogram and black outline)

 

 

 

This symbol means that potential hazardous voltages are present and the equipment must be properly 
grounded and extreme caution should be taken. If for any reason maintenance or repair is needed, 
insure that voltage(s) are disconnected at the machine and the source unless (be cautious) voltage needs 
to be present to troubleshoot the problem, then only qualified personal should work on “live” systems. 
(Yellow background with black pictogram and black outline)

 

 

 

This symbol means that the machine is heavy if the machine needs to be lifted onto or off of a truck, 
loading dock etc. that  proper technique or heavy duty lifting device should be used, personal injury could result. 
(Yellow background with black pictogram and black outline)

 

 
 

This symbol means that dangerous chemicals, gases, dust particles and/or fumes are present including 
carbon monoxide. Proper ventilation must be maintained. Do not use gasoline/diesel/propane powered 
equipment indoors.

 

(Yellow background with black pictogram and black outline)

 

 

 

This symbol means that there are sharp components and if feet/fingers/digits come in contact personal

 

injury or death could result.

 

(Yellow background with black pictogram and black outline)

 

 
 

 

This symbol means hazardous pressures are present. Caution should be exercised to prevent personal 
injury or damage to equipment. Face, eye and head protection should be used.

 

(Yellow background with black pictogram and black outline)

 

 
 

This symbol means explosive and hazardous vapors are present. Caution should be exercised to 
prevent personal injury to face and eyes. Breathing and personal protection should be used when 
servicing.

 

(Yellow background with black pictogram and black outline)

 

Safety Symbols

 

Summary of Contents for TSCP8

















Reviews: