Tomahawk PCR5030 Series Operation And Instruction Manual Download Page 19

Page: 19 / 22

SYMPTOM

POSSIBLE CAUSES

SOLUTION

“Weak in power”
compression is proper
and does not misfire.

Air cleaner not clean.

Improper level in carburetor.

Clean or replace air cleaner.
Check float adjustment, re-build

carburetor.

Defective spark plug.

Clean or replace spark plug.

Engine overheats.

Spark plug heat value improper.

Correct type of fuel.

Replace with correct type of spark plug.

Replace with correct type of fuel.

Cooling fins dirty.

Clean cooling fins.

Rotational speed
fluctuates.

Governor adjusted correctly.

Governor spring defective.

Adjust governor.

Replace governor spring.

Fuel flow restricted.

Check entire fuel system for leaks or clogs.

Recoil starter
malfunction.

Recoil mechanism clogged with

dust and dirt.
Spiral spring loose.

Clean recoil assembly with soap

and water.
Replace spiral spring.

Summary of Contents for PCR5030 Series























Search results

Summary of Contents for PCR5030 Series

Reviews:

Related manuals for PCR5030 Series

Brands by name

Popular brands

Tomahawk PCR5030 Series, Operation And Instruction Manual

Search results

Summary of Contents for PCR5030 Series

Reviews:

Related manuals for PCR5030 Series

Brands by name

Popular brands