Tomahawk PC5030 Series Operation And Instruction Manual Download Page 6 | Manualshive

Page: 6 / 22

background image

6

-ALWAYS keep the area around the muffler free of debris such as leaves, paper, cartons,

etc. A hot muffler could ignite the debris and start a fire.
-NEVER run the engine without the air filter.

1.4 Label Locations

1.5 Safety and Operating Labels

Tomahawk machines use international pictorial labels where needed. These labels are

described next:

«
...
4
5
6
7
8
...
»

Summary of Contents for PC5030 Series























Reviews:

No comments

Related manuals for PC5030 Series

Brand: B&PLUS Pages: 2

Brand: Camo Pages: 7

PS 8000 2U Series

Brand: Elektro-Automatik Pages: 40

Brand: Hakko Electronics Pages: 2

Brand: Dahua Technology Pages: 28

Brand: S.E.F.A Pages: 26

Brand: Parkside Pages: 18

Brand: Stanley Pages: 10

SBP-XFMR Series

Brand: ECO POWER Pages: 21

sunjoe24V-HG100

Brand: SNOWJOE Pages: 52

Brand: FINE INSTRUMENTS CORPORATION Pages: 17

ILUEST NE Series

Brand: Salicru Pages: 60

Brand: FACHOWIEC Pages: 4

Brand: Wacker Neuson Pages: 74

Brand: Shop fox Pages: 64

ELG-150-C Series

Brand: Mean Well Pages: 12

Brand: Airpress Pages: 16

Brand: Villager Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands