cuits. A voltage drop caused by the L.E.D. indicator will result.For
applications where TTL circuits are used, please contact the factory.
WARNING
: An ohmmeter is recommended for testing Reed
Switches. NEVER use an incandescent light bulb as a high current
rush may damage the switch.
Reed and TRIAC switches are only recommended for signalling posi-
tion, not directly powering soleniods. For shifting a solenoid, a relay or
resistor is recommended between it and the Reed Switch. Switch rat-
ings must not be exceeded at any time.
NOTE:
For Hall Effect Switch Magnet, be sure the S pole of the
magnet (indicated with black dot) is facing toward the switch (down).
TO ORDER RETROFIT KITS:
SW (then the model number
and base size, and code for type of switch
needed:
EXAMPLE: SWPB210RM
All Switch Kits come with
1 switch and mounting
hardware.
Female Connector 5M
Loctite® is a registered trademark of the Loctite Corporation,
www.loctite.com
Magnalube®-G is a registered trademark of the Carleton-Stuart
Corporation,
www.magnalube-g.com
SWITCH TYPE CODE
BT
(Form C Reed Switch with 5-meter lead)
BM
(Form C Reed Switch with 5-meter lead and QD)
RT
(Form A Reed Switch with 5-meter lead)
RM
(Form A Reed Switch with 5-meter lead and QD)
CT
(TRIAC Switch with 5-meter lead)
CM
(TRIAC Switch with 5-meter lead and QD)
KT
(Hall-effect Switch (Sinking) 5-meter lead)
KM
(Hall-effect Switch (Sinking) 5-meter lead and QD)
TT
(Hall-effect Switch (Sourcing) 5-meter lead)
TM
(Hall-effect Switch (Sourcing) 5-meter lead and QD)
REED
SWITCH
LOAD
BROWN
BLUE
(-)
(-)
(+)
(+)
REED
SWITCH
LOAD
BROWN
BLUE
(-)
(-)
(+)
(+)
OR
REED SWITCH FORM A
LABEL COLOR: RED
10VA MAX.
200 Vdc
500mA Max. Current
REED
SWITCH
COMMON
NORMALLY CLOSED
NORMALLY OPEN
BROWN
BLACK
BLUE
REED SWITCH FORM C
LABEL COLOR: YELLOW
120 Vdc/120 Vac MAX.
250mA Max. Current
HALL-EFFECT SWITCH
(SINKING)
LABEL COLOR: GREEN
Input Voltage:5-25 VDC only
Output Current: 200 mA Max.
BROWN
BLACK
BLUE
QUICK-DISCONNECT
(Applies to all switch types)
An Important Note Regarding
Field Retrofit of Quick-Disconnect
Couplers:
If replacing a Quick-Disconnect switch
manufactured before 7-1-97
it will also be necessary to replace
or rewire the female-end coupler
with the in-line splice
Female Connector 5M
HALL-EFFECT SWITCH
(SOURCING)
LABEL COLOR: WHITE
Input Voltage:5-25 VDC only
Output Current: 200 mA Max.
UNIVERSAL SWITCH WIRING DIAGRAMS AND
LABEL COLOR CODING
AC
COM
LOAD
INPUT
TRIAC
SWITCH
120Vac
Max.
MOV
BROWN
BLUE
TRIAC SWITCH
LABEL COLOR: BLUE
Max. 1Amp. Cont. Current @ 86°F
Max. .5Amp. Cont. Current @ 140°F
Peak surge current 10Amp.
NOTE:
The side of the switch with
the groove indicates the sensing
surface. This must face toward the
magnet.
For complete Switch Performance
Data, refer to the Tolomatic Fluid
Power Products Catalog 9900-4000
4 – Options
PB208, PB210, PB217
Parts Sheet #2500-4012_07_PB208_10_17ps
3800 County Road 116, Hamel, MN 55340 USA
http://www.Tolomatic.com • Email: [email protected]
Phone: (763) 478-8000 • Fax: (763) 478-8080 • Toll Free: 1-800-328-2174
© 2022 Tolomatic
202205261056
All brand and product names are trademarks or registered trade-
marks of their respective owners. Information in this document is
believed accurate at time of printing. However, Tolomatic assumes
no responsibility for its use or for any errors that may appear in
this document. Tolomatic reserves the right to change the design
or operation of the equipment described herein and any associated
motion products without notice. Information in this document is
subject to change without notice.
Visit www.tolomatic.com for the most up-to-date technical information
