TOHATSU BFT 2000A Owner'S Manual Download Page 42

Page: 42 / 126

6. PRE-OPERATION CHECKS

BFT200A/BFT225A is 4-stroke,
water cooled outboard motor which
uses unleaded regular gasoline for
fuel. It also requires the engine oil.
Check the following before operating
the outboard motor.

Perform the following
pre-operation checks with the
engine stopped.

Before each use, look around and
underneath the engine for signs of oil
or gasoline leaks.

Engine Cover Removal/Installation

1. Pull the engine cover latch.
2. Remove the engine cover by taking

it up.

<Installation>

1. Place the engine cover on the main

body.

2. Slide the engine cover so that the

cover lock on the cover is mated
with the lock in the main body.

ENGINE COVER LATCH

<Removal>

MAIN BODY SIDE

COVER SIDE

COVER LOCKS

Summary of Contents for BFT 2000A































































































































Search results

Summary of Contents for BFT 2000A

Reviews:

Related manuals for BFT 2000A

Brands by name

Popular brands

TOHATSU BFT 2000A, Owner'S Manual

Search results

Summary of Contents for BFT 2000A

Reviews:

Related manuals for BFT 2000A

Brands by name

Popular brands