manualshive.com logo in svg

TodaysHighTech E-707-1, Owner'S Manual

Share
Download
TodaysHighTech E-707-1 Owner'S Manual Download Page 12

TodaysHighTech.com, LLC   5235 Mission Oaks Blvd. #324,   Camarillo CA 93012   805-504-5808 

 

12 

application  disconnects  the  motor.  Check  to make  sure  the  connections  did 
not  come  loose  in  the  battery  box.  Replace  the  brake  assembly  disconnect 
interlock.  This  comes  as  part  of  the  either  the  front  or  rear  hand  brake 
assembly. Check the wire out. You may be able to change, repair, or solder 
the  wire  to  make  the  repair.  This  is  a  big  safety  issue  and  something  that 
should be checked on a regular basis. You do not want that strong 350 watt 
motor running at full speed while you are trying to brake. 

 

Problem

 

Scooter is losing speed within just a few minutes 

 
Possible conditions. 1. Low battery. 2. The temperature is in the freezing range and 
you left your scooter in an un heated space. 3. The temperature is over 100F and 
the unit is over heating. 
 

Possible  Solutions  1.  Recharge  your  battery  for  4-6  hours.  Power  is  good 
again.  If  power  is  still  low  check  the  charger  or  the  battery  needs 
replacement.  2.  Bring  the  scooter  into  a  conditioned  space  and  bring  the 
temperature  up  slowly.  Lead  acid  batteries  do  not  like  low  or  high 
temperatures because of the electro chemical nature of the storage device. 
 
 

Problem 

The front brake is pulsating when I apply pressure to the hand brake. 
 

Possible conditions 1. The rim is bent. 2. The axle bolts are loose 

 

Possible Solutions 1. Carefully check the rim by picking the front wheel off of the 
ground and spin the wheel. If the rim is bent, replace. 2. Carefully check the axle 
bolts. The wheel assembly should spin freely and not drag. You do not want to 
over tighten the axle bolts and place high side loads on the wheel bearings. 

 
 

Problem 

The power indicator by the thumb throttle does not illuminate when the scooter is on. 
 

Possible conditions 1. Battery is discharged. 2. Fuse is blown 

3. Loose connection inside the scooter. 

 

Possible Solutions 1. Recharge your scooter 2. Check and replace the fuse (30 
amp  slow  blow)  3.  Open  the  battery  compartment.  Visually  inspect  all  wire 
connections making sure there are no loose wires. Replace thumb throttle. If the 
lights do not come on but everything else works then it is your choice if you want 
to change the throttle. 

 
 
TodaysHighTech.com is here to help you. Contact us so that we can help you to diagnose 
your equipment. We want to help you get years of service out of every purchase. 

Summary of Contents for E-707-1

















Reviews:

No comments

Brands by name

Popular brands

Load more brands