background image

9

MODE

DEFAULT 

TIME

DEFAULT 

PRESSURE*

MIN - MAX

TIME

MIN - MAX

PRESSURE NOTES

KEEP 

WARM

10 hours

---

After a selected 

cook mode ends, 

the pressure 

cooker shifts to 

a KEEP WARM 

mode. KEEP 

WARM can also 

be used

independently.

*  

The pressure levels programmed into the logic of this pressure cooker are  

 

measured in kPa. The kPa unit of measurement is different from PSI (pounds  

 

per square inch). 1 PSI is approximately 7 kPa.

TIPS AND HINTS

• 

Never load the inner pot above the MAX line (image B). 

• 

The pressure levels programmed into the logic of this pressure cooker are measured 

in kPa. The kPa unit of measurement is different from PSI (pounds per square inch). 

1 PSI is approximately 7 kPa.

• 

Use  the  SAUTE  setting  to  sear  or  brown  foods  directly  in  the  inner  pan  before 

cooking a full meal on a setting with pressure.

• 

If cooking frozen foods without defrosting the foods, adjust the cooking time to add 

an additional 10 minutes.

• 

Pressure cooking requires the addition of some form of liquid. Reference recipes 

online for suggested food to liquid ratios.

• 

The selected cook time does not include the time required to build to pressure.

• 

When the pressure cooker enters KEEP WARM mode, the display indicates the 

time that has passed since the cook cycle was completed and the pressure cooker 

entered KEEP WARM mode.

• 

NEVER pour cold water into a hot pressure cooker.

• 

If the lid is in the closed position and excess steam is noticed between the lid and 

pressure cooker housing, it is possible the lid is not seated properly and the rubber 

gasket ring has not formed a full seal. Try pushing down the lid firmly. The safety 

valve may also be stuck. It is important to regularly check the safety valve when the 

pressure cooker is not in use to make sure it moves up and down and the silicone 

ring meets the inner lid without gaps.

• 

The condensation container will help to drain any excess liquid that gathers around 

the rim of the pressure cooker body. Insert and remove the condensation container 

by sliding it on and off of the rails (image I).

• 

The pressure cooker housing includes a convenient spoon slot to store the plastic 

spoon (image J).

Summary of Contents for TM-670PC













Reviews: