TMB ProPlex IQ Two 416 User Manual Download Page 22 | Manualshive

Page: 22 / 26

background image

- 22 -

RDM OFF/ON

:

Set the RDM settings for selected DMX port.

What is RDM?

Remote Device Management or RDM is a protocol enhancement to DMX512 allowing bi-directional
communication between a lighting or system controller, and attached RDM-compliant devices over a
standard DMX line. This protocol allows configuration, status monitoring, and management of these devices
in such a way that does not disturb the normal operation of standard DMX512 devices that do not recognize
the RDM protocol. (source: http://www.rdmprotocol.org/)

Note

:

Use the RDM when using sACN protocol because sACN doesn't support it. If using sACN and want

to RDM functionality, switch to ArtNet for the moment RDM is needed.

«
...
20
21
22
23
24
...
»

Summary of Contents for ProPlex IQ Two 416



























Reviews:

No comments

Related manuals for ProPlex IQ Two 416

Brand: Palmer Pages: 8

IMI SENSORS 042M35

Brand: PCB Piezotronics Pages: 6

Brand: PCB Piezotronics Pages: 5

Brand: BVF Pages: 2

Brand: hager Pages: 2

FD21204-48SRC Series

Brand: CommScope Pages: 20

Brand: Chauvet Pages: 20

Brand: Chauvet Pages: 116

Plastic Fiber Optic Assembly PBPS26U

Brand: Banner Pages: 2

Brand: Respironics Pages: 12

Brand: Gude Pages: 92

Brand: LEISUREWIZE Pages: 2

Gravity Sure-Line

Brand: MSA Pages: 60

Brand: Digitogo Pages: 7

Brand: INOAGE Pages: 2

Raychem FrostGuard

Brand: Pentair Pages: 8

Brand: Arrel Audio Pages: 12

Brand: Lincoln Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands