background image

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5

18

Operator's Manual

LOCKDOWN 21-FT 2-MAN Ladder Stand

SET UP AND USE INSTRUCTIONS

 

During installation and removal of ladder treestands, 

you must always and properly use the included Full Body 

Harness (Fall Arrest System). Refer to the Full Body Harness 

instructions included with this product for proper use.

WARNING

Never use a treestand on a dead, leaning, diseased or 

loose barked tree, or a utility pole. Always avoid electrical  

power lines.
Bring ratchet strap(s) up with you in a pocket - Do not 

carry in your hands!

WATCH THE SET-UP AND USE VIDEO ONLINE AT  

WWW.HUNTRIVERSEDGE.COM  

TO ASSIST WITH THE SET-UP OF YOUR TREESTAND

1.  Select a straight, healthy tree. Do Not attempt to install on a tree 

that is not healthy.

2.  Place the assembled product lying on the ground in front of the 

tree with the bottom ladder section approximately five feet away 

from the base of the tree.

3.  Position one person at bottom end of ladder. This person has to 

prevent the ladder end from tilting up and from skidding across 

the ground when platform end is lifted.

4.  Position two people at the platform end of the ladder, lift the 

platform end and continue uprighting by walking toward bottom 

end of ladder while moving hands along ladder rails. Stand ladder 

up against chosen tree on dry, level ground. Use caution when 

ladder comes over center against the tree, as shown by arrow “A”. 

SEE FIGURE 2.

5.  Once elevated completely, carefully slide the base so that the 

sitting and standing platforms are parallel to the ground, as 

shown by arrow “B”. SEE FIGURE 2.

6.  Step back and look at the ladder top to see that both the lower 

platform tree blade and upper tree blade are contacting the tree. 

Adjust as needed so both of the tree blades are contacting the 

tree.

7.  Step down hard on bottom step to push ladder legs into the 

ground, as shown by arrow “C”. SEE FIGURE 2.

8.  While two people hold the stand in place, the third person should 

complete the necessary steps on following pages to secure the 

stand to the tree.

A

A

C

B

FIGURE 2

Summary of Contents for RIVERS EDGE LD202





























Reviews: