Boltek EFM-INV-M Installation Instructions Manual Download | Manualshive

Page: 1 / 13

background image

10/15/2020

(C) 2020 BOLTEK CORP

EFM-INV_Instruction_1.3

Boltek EFM-INV-M / EFM-INV2 / EFM-INV3

Inverting Mounting Kit

Installation Instructions

Introduction

The EFM-INV-M, EFM-INV2, and EFM-INV3 Inverted Mounting Kits will allow you to mount your EFM-100 or EFM-
200 Electric Field Mill in the inverted downward-facing configuration. Inverting your field mill will provide you with
reduced precipitation noise.

ELECTROCUTION WARNING:

INSTALLATION THIS PRODUCT NEAR POWERLINES IS DANGEROUS.

FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS.

SEE ADDITIONAL WARNINGS ON REVERSE

1
2
3
...
»

Summary of Contents for EFM-INV-M














Reviews:

No comments

Related manuals for EFM-INV-M

Brand: Datalogic Pages: 2

Brand: Zen Space Desks Pages: 3

Brand: RackSolutions Pages: 4

Mounting Plates SM-Series

Brand: Sonance Pages: 2

Brand: Mail Boss Pages: 2

Brand: Wali Pages: 12

Brand: ZANE ARTS Pages: 10

Brand: Sanus Pages: 60

Brand: Roland Pages: 2

Brand: parktool Pages: 2

Brand: Linkedpro Pages: 2

Brand: USX-MOUNT Pages: 14

MultiMount MM-060

Brand: Allen Products Pages: 3

Brand: BVE Pages: 7

Brand: Bosstab Pages: 2

Brand: Konig & Meyer Pages: 2

Brand: Konig & Meyer Pages: 2

Brand: Konig & Meyer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands