TLV COSPECT M-COS-16 Instruction Manual Download Page 24 | Manualshive

Page: 24 / 36

background image

172-65188M-08 (

M-COS 3,16,21

Pressure Reducing Valve) 24 Jun 2015

23

<Valve>
Disassembling the Pilot Section

The diaphragm is removed by utilizing the notch in the pilot body. Loosen the pilot
valve seat with a box wrench and remove it. Lift the pilot valve spring up and out with
a pair of tweezers. Then loosen and remove the pilot screen holder to remove the
pilot screen.

→Check for any fault on the pilot valve seat, flaws on the gaskets and clogging of

the pilot screen.

Check for deformation, corrosion or faults on the diaphragm. The diaphragm
should be convex (open downward), with the printed “UP” mark on the top.

Notch

Diaphragm

Pilot Valve Seat
& Gasket

Pilot Cover

Bolt

Pilot Body

& Gasket

Pilot Screen

Pilot Screen Holder & Gasket

Pilot Valve

Pilot Valve Spring

Diaphragm

Pilot Valve Seat
& Gasket

Pilot Valve

Pilot Valve Spring

Notch

Bolt

Pilot Body

& Gasket

Pilot Screen

Pilot Screen Holder & Gasket

15 – 50 mm

65 – 100 mm

«
...
22
23
24
25
26
...
»

Summary of Contents for COSPECT M-COS-16





































Reviews:

No comments

Related manuals for COSPECT M-COS-16

Brand: Parasound Pages: 72

Brand: Jafar Pages: 15

Brand: KAR-TECH Pages: 28

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

ECL Comfort 110

Brand: Danfoss Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands