background image

 

3.TURN ON THE DEVICE 

 

Open the rubber cover, insert the SIM card(chip up) to the slot.

 

 

The indicator light is on when SIM card is inserted. 

 

After device is on, pls connect device with car based on above wire connection diagram. 

 

The  device  gets  GPS location  when  there  is  GPS  signal  and  gets  LBS  location  when  there  is  no  GPS 

signal. 

 

The device automatically turns off when the SIM card is removed. 

 

 

4.SMS TRACKING 

  4.

1. Call the SIM card phone number in tracker,you will receive a Google Maps link of position, 

 

or sending message “

G123456#

” to SIM card phone number in tracker . 

      E.g: 

 

 

 

4.2.  Admin  number  setting  (After  admin  number  setting,  all  SMS  operations  to  the  device  are  under  this 

number only.) 

Command: 

admin123456 phone number

This phone number is your own mobile phone number , not the 

SIM card number in tracker .

 

Reply

admin ok

 

E.g

admin123456 13265790180 

 

When the unit is in over-speed alarm, shake sensor alarm, or low battery alarm, it will send alert to the admin 

number.

13265790180

 

Admin number Canceling: 
Command 

noadmin123456

 

Summary of Contents for TP-GPS806













Reviews: