ENVIRONMENTAL CONDITIONS
•
Ambient temperature from 5 to 40° C.
•
Relative humidity max. 80% for temperatures up to 31° C with linear decrease up to
50% at the temperature of 40° C condensing included.
•
Atmospheric Pressure from 500 to 1060 hPa.
•
Voltage supply variation not higher than
±
10%.
•
Value of transitory over-voltage in conformity to the installation category (which
provides for 2500V).
INSTALLATION
The device has been calibrated and tested at factory and as such does not require any
further calibration or adjustments before installation and start-up.
Unpack the device and follow the next advices:
1.
Position the device on a levelled flat, hard and smooth surface, established with non-
infiammable material.
2.
Allow space not lower than 10 cm from walls and surrounding furniture.
3.
Do not install the device nearby water sinks or similar to avoid contacts with
water or substances which could cause electrical short-circuit to the system.
4.
Install the device in a well aerated location, not near windows or external doors which
could cause an unnatural circulation of the air inside the device and therefore
compromise its correctly running.
5.
Do not install the device nearby heat sources or near other electrical devices.
6.
Install the device in such a way that the power cable is never twisted or bent, but it
should connect to the socket free and unhindered. Avoid to positioning the power cable
nearby heat sources or other devices that shall caused damage on it in a long run.
7.
In the event the device is placed on a trolley, always check that the lower part of the
device is not enclosed or hindered, as to allow continuos and sufficient ventilation.
Once the device is correctly installed and power cable connected, it’s ready for use.
SAFETY WARNINGS
•
The device is designed for use in internal locations.
•
The device is not designed for use in presence of gasses or explosive vapours.
•
No water or other liquids should be poured into device neither on its base.
•
Before any cleaning or maintenance actions, the power cable must always first be
removed.
•
Make sure that the electrical system has electrical grounding and that it’s in conformity
to the safety norms in the country of installation.
•
Do not remove any label or plate, in case of need, ask for more.
•
Always insist on original spare parts.
•
Do not open the door of the device until the thermometer of the internal temperature do
not indicate a temperature lower than 30°C.
TIME – PROGRAMMED RUNNING
1.
Insert the supplied connection socket of the mains cable in the plug of the device
(Pos. 4) and the feeder- plug in the wall mains socket, after checking the voltage value.
2.
Turn the thermoregulator knob (Pos. 1) and set the desired temperature. This operation shall
always be carried out when device is cold.
3.
Place materials to be sterilized inside the device.
4.
Lock up the door (Pos. 8).
5.
Set, by turning the timer knob (Pos. 2) anti-clockwise, the sterilization time adding necessary
time in order to bring the device and the material inside to the desired temperature.
The
necessary time to reach the temperature of 180°C is about 30/40 minutes in case of empty
chamber sterilizer, and about 60 minutes with Loaded Chamber well arranged on the
trays.
This operation switch on the warning light (Pos. 5) indicating that the device is working
and the warning light “resistance” (Pos. 6) indicating that the resistances are turned on in the
circuit. The graduated thermometer (Pos. 3) allows to check the progressive increase of the
internal temperature. When the internal temperature has reached the programmed value, the
warning light “resistance” (Pos. 6) is turned off for then, after brief time, again turned-on
indicating the re-connection of the resistances in the circuit. This operation allows to keep
inside the device a constant temperature up to the end of the sterilization cycle. After
programmed time has elapsed, the device turns itself off automatically.
In order to maintain an even temperature inside of the heating chamber and to allow a better
circulation of the air, the device is featured with a ventilation motor fan internally wired.
CONTINUOS -CYCLE RUNNING
The device has also a continuos-cycle running. For use this kind of running proceed up to
point 4 of the procedure for time-programmed running described above. Turn, at this
moment, the timer knob (Pos. 2) anti-clockwise. The indefinite-time manual continuos-
cycle is inserted with a click. To turn off the device, turn back the timer know to position 0.
3
4
