manualshive.com logo in svg

Titanium MIG 140, Owner'S Manual & Safety Instructions

Share
Download
Titanium MIG 140 Owner'S Manual & Safety Instructions Download Page 13

Page 13

For technical questions, please call 1-888-380-0318.

Item 64804 64805 
        

Sa

FE

ty

Maint

E

nanc

E

Ba

S

ic W

E

lding

W

E

lding 

t

ip

S

S

E

tup

20.  Make sure the welding wire is resting in the groove 

of the Feed Roller, then push the wire Idler Arm 
down, and swing the Feed Tensioner up to latch it 
across the tip of the arm.   
After the wire is held by the Tensioner, 
you may release it.

note:

 The tension should be 3 – 5 for solid wire and 

2 – 3 for flux-cored wire.  Too much force on flux-cored 

wire will crush it and may cause feeding issues.

21.  Pull and twist the Nozzle to remove it.

22.  Unscrew the Contact Tip 

counterclockwise and remove.

23.  Lay the MIG Gun Cable out in a straight line so 

that the welding wire moves through it easily.  
Leave the cover open, so that the feed 
mechanism can be observed.

iMpORtant

Stainless steel wire is less flexible than 

other welding wire.  therefore, it is more 

difficult to feed through the liner and gun.  

it is especially important to keep the gun cable 

straight while feeding stainless steel wire.

WaRning

The following steps require applying power to the Welder  

with the cover open.

to prevent serious injury from fire or electric shock:

1. 

do not touch anything, especially not the ground clamp, 
with the gun or welding wire or an arc will be ignited.

2. 

do not touch internal Welder components 
while it is plugged in.

24.  Turn the Power Switch off and do not touch the 

Gun’s Trigger and before connecting Power Cord:

a. 

64804 only:

 Plug the Power Cord into a 

properly grounded, GFCI protected 120 VAC 

(20 amp rated) receptacle that matches the 
plug and turn the Power Switch ON.

b. 

64805 only:

 

iMpORtant: change the 

Voltage Switch on the back of the Welder 
to the voltage of the outlet you will use.

  

If using 120VAC, connect the included 
adapter to the end of the Power Cord.  If using 
240VAC, do not use the adapter.  Plug the 
Power Cord into a properly grounded and rated 
receptacle that matches the plug and selected 
voltage and turn the Power Switch ON.

note:

 The circuit must be equipped with delayed 

action-type circuit breaker or fuses.

idler arm

Feed tensioner

power 

Switch

Voltage 

Switch 

(64805 only)

240V to 120V plug adapter

(64805 only)

Voltage switch and plug need to 

be changed at the same time.

nozzle

contact

tip

Mig gun

Summary of Contents for MIG 140

































Reviews:

No comments

Brands by name

Popular brands

Load more brands