background image

 

TITAN Technologies International, Inc.

® 

9001 Jameel Street,  Suite 180 •  Houston, TX 77040 

Toll-Free: 866.345.8484 • Phone: 281.449.9994 • Fax: 281.449.9996 • Email:[email protected]   

http://www.titanti.com 

Trouble Shooting Chart

 

 
Most faults have a simple cause and can therefore be rectified on site, i.e. time 
losses and transport costs can be avoided. Some of the most frequent faults are 
explained below. If this information is insufficient, please consult our technical 
support or your authorized 

TITAN

®

 Repair Facility. 

 

Pump does not pressurize

 

  Air in pump   

 

 

Switch motor on and off several times 

  Changeover valve jammed  

Switch by hand 

  Pressure converter defective 

Replacement necessary 

 

Pump pressurizes inadequately

 

  Air in pump   

 

 

Switch motor on and off several times  

  Gear wheels worn out 

 

Replacement necessary 

 

Pump does not reach pressure 

 

Pump 

worn 

   Replacement 

necessary 

  Valve worn   

 

 

Leak to tank 

  Relief valve misadjusted   

Adjust pressure limiting valve 

 

Pressure cannot be relieved 

  Solenoid valve jammed 

 

Switch by hand 

 

Technical data 

 

1. Gear pump 

 

Operating pressure p max:  

230 bar  

Conveyed volumes:  

 

LP – 1.5 l/min until 4 l/min up to 230 bar 

 

2. 

Pressure Intensifier

 

3.  

Converting ratio 

  

 

1:13 

Operating pressure p max:  

2500 bar 

Conveyed volumes:  

 

HP – 0.9 l/min up to 2500 bar 

 

 
 
 
 
 

Summary of Contents for WindMaster 2010


















Reviews: