Titan PROTOUCH Owner'S Manual Download

Page: 16 / 20

English

Troubleshooting

Problem A: Motor will not run

Cause

Solution

Battery pack not charged. Electrical problem or defective

motor

Recharge the battery pack. Call Technical Service.

Bad fuse due to abnormal loading

Call Technical Service

Problem B: Motor has a low hum and does not spray

Cause

Solution

Control knob turned in too far

Turn control knob counterclockwise

Seized piston

Disassemble sprayer and clean

Problem C: Motor operates properly but does not spray

Cause

Solution

1. Loose or damaged suction tube

Tighten or replace

2. Plugged or worn atomizer valve

Clean or replace as needed

3. Atomizer valve missing

Replace atomizer valve

4. Material too thick

Thin material

5. Plugged spray tip

Clean tip

6. Intake filter plugged

Clean intake filter

7. Control knob needs adjusting

Adjust

8. Worn piston

Clean and oil, or replace

Problem D: Material spitting or globbing

Cause

Solution

1. Low on paint

Refill container

2. Material too thick

Thin material

3. Loose suction tube is drawing in air

Clean and insert firmly into intake opening on pump housing

4. Worm atomizer valve

Replace atomizer valve

5. Worn spray tip

Replace if worn

6. Control knob needs adjusting

Adjust

7. Worn piston

Clean and oil, or replace

Problem E: Excessive fogging

Cause

Solution

Pressure too high

Turn flow control knob clockwise to reduce pressure and flow

Holding sprayer too far from work surface

Hold sprayer closer to work surface

Any attempt to open the motor housing or repair any

electrical parts within the unit by anyone other than

an authorized repair technician could cause serious

injury and will void the warranty.

Summary of Contents for PROTOUCH





















Search results

Summary of Contents for PROTOUCH

Reviews:

Related manuals for PROTOUCH

Brands by name

Popular brands

Titan PROTOUCH, Owner'S Manual

Search results

Summary of Contents for PROTOUCH

Reviews:

Related manuals for PROTOUCH

Brands by name

Popular brands