background image

17 

 

SECTION 3: ADJUSTMENTS 

 

DISCHARGE CHUTE ANGLE 

1.

 

Push down on rotation chute lock lever (#1) and 
hold together with handle (#3). 

2.

 

Rotate discharge chute (#2) in small increments 
until desired angle of discharge is achieved. 

3.

 

Release lock lever (#1). Make sure lever has 
locked into position and chute cannot rotate. 

 
 

 

Figure 3-1: Adjust Discharge Chute Angle 

DEFLECTOR CHUTE ANGLE 

1.

 

Remove the chain loop from the holder on one 
side of the discharge chute. 

2.

 

Pull or loose the chain to rotate deflector chute 
(#1) up or down to the desired angle.  

3.

 

Hang the chain loop on the holder 

 
 
 
 
 

 

Figure 3-2: Adjust Deflector Chute Angle 

 

CHECK LEDGER KNIFE CLEARANCE 

To avoid serious injury or death: Knives and ledgers are sharp. ALWAYS wear gloves and eye 

protection while inspecting and adjusting ledger clearance. 

 

IMPORTANT:

 It is best to have two people available to check ledger knife clearance; or have in 

place a way other than the pivot latch to securely 
support the feed chute rotate up; or remove the 
feed chute from the chipper lower frame. 

Figure 3-3: View of Rotor Knife (#4) and Ledger 
Knife (#5) 

The knives (#4) cut best if knife ledger (#5) is 
adjusted with 1mm to 1.5mm gap between

 

cutting edge of knives and knife ledger. The 
larger the gap, the faster the product with self- 
feed. Do not exceed 1.5mm gap. 
 

Summary of Contents for 198268


































Reviews: