background image

running. Extinguish cigarettes, cigars, pipes 
and other sources of ignition. 
 
Controls and Features 
 
Blade Control 
The blade control is attached to the upper 
handle of the mower. Depress and squeeze it 
against the upper handle to operate the unit. 
Release it to stop engine and blade. 
 
WARNING: This blade control is a safety 
device. Never attempt to bypass its 
operations. 
 
Cutting Height Adjustment Lever 
The cutting height adjustment lever is located 
above the left rear wheel. To adjust the 
cutting height, refer to the assembly & Set-Up 
section. 
 

Drive Control 
The drive control is located on the upper 
handle. Squeeze the drive control to engage 
the drive system. Release the drive control to 
slow down when approaching an obstacle, 
making a turn, or stopping. 
 
Side Discharge Chute 
Your mower is shipped as a mulcher. To 
discharge the grass clippings to the side 
instead, follow the instruction in the 
Assembly and Set-Up section to attach the 
side discharge chute. 
WARNING: Keep hands and feet away from 
the chute area on cutting deck. Refer to 
warning label on the unit. 
Recoil Starter 
The recoil starter is connected to the support 
rod and is located on the right side of the 
lower handle. Stand behind the unit and pull 
the recoil starter rope to start the unit. 

 

 

Summary of Contents for TPKH822
























Reviews: