Kronus 1 – Temperature and
Humidty Controller
The Kronus 1 is used to independently maintain the temperature and humidity levels in
your growing environment. Both temperature and humidity can be adjusted by setting the
dials on the front of the controller to your preferred settings. If the temperature exceeds the
predetermined setting then an exhaust fan is activated and will run until the temperature is lower
than the set point. If the humidity exceeds the predetermined setting, then the dehumidifier
is activated and will run until the humidity is lower than the set point. After the temperature or
humidity has lowered below the selected temperature or humidity level, the equipment will turn
off and be on standby until the next event occurs.
The Kronus 1 allows up to 15 amps of maximum capacity on a standard 120 Volt circuit. The
Kronus 1 is built with the highest quality components to provide the user with years of trouble
free service.
Instructions for Operation
• Securely mount your Kronus 1 in your grow area and away from any moisture, spray,
pesticides, etc.
• Plug your dehumidifier into the “Dehumidify Output’ outlet.
• Turn the dehumidifier ‘ON’ to the highest setting possible.
• Plug your exhaust fan into the “Exhaust Fan Output’ outlet.
• Turn the exhaust fan ‘ON’ to the highest setting possible.
• Set the ‘Temperature’ and ‘Humidity’ dials at the preferred temperature and
humidity levels for your garden.
• Place the remote sensor in the grow area up to 25 feet away from
the Kronus 1 at plant canopy height.
• Plug the Kronus 1 into a maximum 120 Volt – 15 Amp circuit outlet.
• Use of a surge protection device is recommended to protect your
Kronus 1 from potential damage.
• Turn the Kronus 1 power switch to the ‘ON’ position.
• Your Kronus 1 will now control your equipment at the desired settings .
Troubleshooting Tips
If the Kronus 1 is not performing as expected, try the following:
a. Make sure that the power switch is lit and in the ‘ON’ position.
b. Confirm that your power source is active by using a voltage test meter and
providing 120 Volts to the controller.
Warranty Information
• Titan Controls warrants the original purchase of this product against defects in material and
workmanship under normal use for three (3) years from the date of purchase.
• During the warranty period, Titan Controls will, at our option, and without charge, repair or
replace this product if the controller or any of its components fail or malfunction.
• All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA)
number prior to any service of the product.
• This warranty is expressly in lieu of all other warranties, expressed or implied, including the
warranties of merchantability and fitness for use and of all other obligations or liabilities on the
part of the seller.
• This warranty shall not apply to this product or any part thereof which had been damaged by
accident, abuse, misuse, modification, negligence, alteration or misapplication.
• Controllers with serial numbers or date tags that have been removed, altered or obliterated;
broken seals or that show evidence of tampering; mismatched board serial numbers or
nonconforming parts, are excluded from coverage.
• Titan Controls makes no warranty whatsoever in respect to accessories or parts not
supplied by Titan Controls.
• Monetary refunds of the warranty will not be given.
• The Buyer assumes all responsibility regarding the use & installation of this controller.
• All warranty service is provided through the factory or an authorized service representative.
• This warranty shall apply only to the United States, including Alaska, Hawaii and
territories of the United States.
• Defective controllers need to be returned with the “proof of purchase/receipt”.
• For additional warranty information, contact a Titan Controls Technical
Service Representative or your Dealer.
• NOTE: Titan Controls is a manufacturer of environmental controls. All sales offerings to the
public are done through a nationwide group of Dealers. No sales offerings will be made
directly to the general public.
Service and Repair Program
• For all service and repairs please contact one of our Technical Service Representatives f
or a Return Merchandise Authorization (RMA) number.
• All factory service & repairs will be completed within 48 hours of receipt of controller
and after authorization by customer for repairs.
• Titan Controls will, at its discretion, repair or replace the controller.
• Factory calibration services are available for all Titan Controls. Returning Units:
Please contact your retail store for returns.
