Receiver Disassembly / Assembly
(continued on page 12)
11
E
N
G
L
I
S
H
10
E
N
G
L
I
S
H
Air Supply Cylinder Removal
❏
Eye protection designed for paintball use must be worn by the user
and any person within range.
To remove a charged air supply cylinder:
1)
❏
Install the barrel sleeve (see page 2).
2)
❏
Turn the cylinder approximately 3/4 of a turn counterclockwise
or out. This allows the air supply pin valve to close so that no air will
enter the marker.
3)
❏
Point the marker in a safe direction and fire the remaining gas in
the marker by pulling the trigger until the marker stops firing. This may
take 4-5 shots.
• If your marker keeps firing after you have turned the tank 3/4 of a
turn, the tank pin valve has not closed yet and you may have to turn
the tank counterclockwise
a little further.
• If you turn the tank 3/4 of a turn and it begins to leak before you pull the
trigger you have turned it too far and may have damaged the tank o-ring.
• Because of the variances in tank valve parts, each tank varies slightly
on exactly how far it should be turned. If this process does not work
the tank pin valve could be too long.
NOTE: Before storing or disassembling be sure to follow
❏
Unloading
Your Marker and
❏
Air Supply Cylinder Removal instructions (see
above).
❏
Install barrel sleeve (see page 2).
Cleaning & Maintenance
❏
Eye protection designed for paintball use must be worn by the user
and any person within range.
To reduce the chance of accidental discharge: First follow
❏
Unloading
Unloading Your Marker
❏
Eye protection designed for paintball use must be worn by the user
and any person within range.
To unload your marker:
1)
❏
Install the barrel sleeve (see page 2).
2)
❏
Empty and remove the hopper.
3)
❏
Go to a designated firing area and remove the barrel sleeve.
4)
❏
Point your marker in a safe direction and fire several times to
be sure there are no balls lodged in the chamber and / or barrel.
IMPORTANT: Do not uncock your marker as uncocking your marker
may push a ball into the chamber or down into the barrel in which
case the ball will be hidden from view.
5)
❏
Install the barrel sleeve (see page 2).
6)
❏
Visually inspect the Cyclone
TM
Feeder and chamber for paintballs.
Cleaning and Maintenance
(continued on page 11)
Cleaning and Maintenance (continued from page 10)
❏
Inspect and lubricate the internal drive assembly parts:
❏
the
front bolt o-ring,
❏
the rear bolt o-ring,
❏
the linkage arm and the
drive spring / guide pin (see Drive Assembly Removal and
Installation instructions on page 13).
❏
Inspect and lubricate
the barrel o-ring and the air supply valve
o-ring with a few drops of oil.
• To clean inside the barrel:
❏
remove barrel and insert metal tab
of cable squeegee into barrel, then pull squeegee through barrel
to remove debris.
Your Marker and
❏
Air Supply Cylinder Removal instructions (see
page 10) and never disassemble a marker that is under pressure.
• Follow warnings listed on the air supply cylinder for handling and storage.
• Familiarize yourself with instructions listed on air supply cylinder
or adaptor. Contact the air supply cylinder or the adaptor
manufacturer with any questions.
• Do not use any petroleum based cleaning solvents.
• Do not use any cleaning solvents that come in aerosol cans.
NOTE: Petroleum based products and aerosol products can
damage your markers’ o-rings.
• To clean your paintball marker:
❏
use a damp towel with water to
wipe off paint, oil, and debris.
❏
Use Tippmann
®
paintball marker
oil or other premium paintball marker oil to lubricate and maintain
your marker in good working condition.
Marker / Receiver Disassembly & Assembly
❏
Eye protection designed for paintball use must be worn by the user
and any person within range.
1)
❏
First follow
❏
Unloading Your Marker and
❏
Air Supply Cylinder
Removal instructions on page 10. Remove air supply before any
disassembly. Do not pressurize a partially assembled paintball marker.
2)
❏
Put the marker in the uncocked position. To uncock the marker:
hold the bolt cocking handle
back - then pull the trigger and release
handle forward which will uncock the marker.
3)
❏
To remove the hopper
:
turn the hopper clockwise
and lift out.
4)
❏
To remove the Front Grip
:
Remove short push pin
/ and
long push pin
and slide the
front grip off.
5)
❏
To remove the Barrel
:
Twist the barrel counterclockwise
to remove.
