Time VERSALIFT VST-7500-I, Operator'S Manual

Page: 21 / 52

3-3
29084-05 03/17 VERSALIFT VST-7500-I
SPECIFICA
TIONS
ground clearance and penetration to be determined
at installation. At maximum extension the outriggers
provide 158 in. (4.0 m) of spread and from 6 in. to 11
in. (152 mm to 280 mm) of penetration based on a 40
in. (1.02 m) frame height. Outriggers are equipped
complete with pilot operated check valves, internal
thermal relief valves, and separate operating controls
for each outrigger. A slide pad at each leg ensures
smooth operation. The standard pivot feet swivel a
minimum of 10° each way.
RADIAL OUTRIGGERS - Radial outriggers are
designed and constructed from high-strength steel.
At 11 in. (0.28 m) of penetration the outriggers provide
211 in. (5.36 m) of spread based on a 40 in. (1.02 m)
frame height. Outriggers are equipped complete with
pilot operated check valves, internal thermal relief
valves, and separate operating controls for each
outrigger.
OUT AND DOWN OUTRIGGERS – Out and down
outriggers are designed and constructed from high-
strength steel and provide 8 in. (200 mm) of penetration
and 195 in. (5.0 m) of spread based on a 40 in. (1.02
m) frame height. Outriggers are equipped complete
with pilot operated check valves, internal thermal relief
valves, and separate operating controls for each
outrigger.
SUBFRAME – The full-length subframe is constructed
of 6 x 8 tubing. Shear plates are provided to attach to
the chassis frame.
BACKUP PUMP - The backup pump is driven by a
DC motor, which is powered by the truck-engine
battery. The system is connected in parallel with the
main pump and is designed for non-continuous
operation. An air cylinder at the upper controls and a
toggle switch at the turret are used to energize the
system.
SECOND SET OF TOOL POWER PORTS - A second
set of tool power ports are installed at the platform to
accommodate a second open center tool.
TOOL POWER AT THE GROUND CONTROLS - The
hydraulic tools must be open-center. The tool circuit
provides approximately 6 gpm at engine idle and 10
gpm with the throttle control engaged. The tool
pressure is 2000 psi (140 Bars)
EXTRA CONTROL CIRCUIT - Consists of an
additional air cylinder at the platform, toggle switch at
the pedestal, pressure switch in the turret and airline
to the platform. An additional pass in the collector
ring is required for each control circuit.
CATEGORY B DIELECTRIC TESTING AND
CERTIFICATION
- Testing and certification for ANSI
A92.2 Category B 46 KV and below or 69 KV is
available. Aerial device may be designed and
configured for gloving work provided it meets the
requirements per ANSI A92.2 category B. The test
system includes interior and exterior test bands and
bonding of all interior boom parts at the elbow end of
the upper boom. The components are wired to a single
external plug. This option includes vacuum prevention
for all the hydraulic hoses routed through the insulated
booms.
COMPONENTS TO ALLOW CATEGORY A
CERTIFICATION
– Consists of interior and exterior
test bands, test band shields, corona ring, sealed
inner boom, aluminum platform liner, and bonding of
boom tip components. This option allows the customer
to certify unit up to 345 kv per ANSI A92.2 Category
A. Aerial device may be designed and configured for
gloving work provided it meets the requirements per
ANSI A92.2 category A. The certification test is to be
provided by the customer after delivery. This option
includes vacuum prevention for all the hydraulic hoses
routed through the insulated booms.
CATEGORY D DIELECTRIC TESTING AND
CERTIFICATION -
Testing and certification for ANSI
A92.2 Category D are available. These aerial devices
which are designed and manufactured for work in which
the insulating system is not considered as primary
insulation, but secondary. These aerial devices are
NOT designed for gloving work methods. They are
rated at voltages of 46kv.
PLATFORM VARIATIONS :
24 in. x 30 in. (0.61 m x 0.76 m) Closed Fiberglass
Platform
24 in. x 42 in. (0.61 m x 1.07 m) Closed Fiberglass
Platform
PLATFORM COVER - Vinyl covers are available for
the platforms.
PLATFORM LINER - Platform liners are available for
each of the closed platforms.
LIFTING EYE - A lifting eye attachment near the
knuckle end of the lower boom/compensation link has
a 1500 lbs. (680 kg) maximum capacity.
1000 LBS MANUAL JIB AND WINCH - The material
handling jib and winch consists of a winch and a jib
pole that are automatically leveled with the platform.
This jib provides 1000 lbs. jib capacity in any boom
position.