Timberk THU UL 06, Instruction Manual

Page: 5 / 16

5
ENGLISH
9 . CLEANING YOUR ULTRASONIC HUMIDIFIER
The method of keeping clean:
Using purified water
Cleaning the base of unit, water tank and ultrasonic transducer every week
Always change to use clean water.
Always drain the water tank when not in use.
Clean all parts of the humidifier before storing by wiping with a damp cloth,
and buffing with a dry cloth.(Except for the electrical control when the unit is
off, any part of the humidifier may be wiped with a soft damp cloth, and
buffed with a dry cloth ,ensuring the unit is unplugged.)
The methods of cleaning the connector:
To clean the dirty surface with a soft brush.
Rinse the transducer with clean water.
The methods of cleaning the base of unit:
Clean the dirty flume with soft cloth .
If there is dirty on the surface of the protective switch of water line, using soft
brush to clean .
Wash the flume with clean water.
ATTENTION!
In order to avoid deformation and erase the working surfaces, leading
to reduced sputtering or other problems, do not use wire brushes,
talcum powder or blades to wipe the transducer.
When strong shocks the water tank can leak.
When the water leaks immediately discontinue operation of the unit
and contact your dealer.
To maintain the unit in a dry state to remove the water after cleaning
and be sure to dry the water tank and the enclosure.
Make sure that inside the water tank and the enclosure is left of water.
Before long a pause in the use of the device dry reservoir and surface of
the device, install the tank in the housing and pack the humidifier
in a plastic bag and then into the box.
Keep the instrument in a room with low humidity.
Storage device in unseasoned state leads to mold.
www.timberk.com electric humidifier
6 . FILLING TANK WITH WATER
Before filling the tank with clear dispenser tank. If you do not, by turning the
tank, spray drops. Without the spray device can not operate. When you
move the humidifier does not grasp the handle of the tank. Necessary to
hold the damper at the base.
1. Remove the sprayer, and then the water tank from the device.
2. Grasp the handle on the tank and pull it up.
3. Unscrew the tank counterclockwise.
4. Fill the tank with water.
5. Screw the lid on the tank clockwise.
Make a tight lid lock tank. Make sure that the rubber ring is installed on top
of the tank. Tighten the lid clockwise.
Incomplete implementation of the above measures lead to ingress of air
into the water tank and as a result of a malfunction.
6. Set the tank and spray on the device.
7. OPERATION
Connect the device to the mains. Pre-fill the tank with water.
To turn the unit on, turn knob (8) the right to On.
(see Fig.1)
Then turn the knob of the intensity output pair (7) clockwise until it stops
(maximum capacity). After about half a minute the device should go for
maximum performance in moisture.
To control the intensity of the steam turn the knob (7) to the left and right.
(see Fig. 2) Upon fall of water level in the reservoir lower minimum allowed
the ultrasound membrane of the device cuts out automatically. The red
detector lights up on the control panel. To continue the device functioning it
is necessary to fill the reservoir with water in accordance with the paragraph
6 Filling the reservoir with water.
To turn the unit off, turn knob (8) in the left to Off. (see Fig. 2)
8 . THE FILTER CARTRIGE
The set of the unit includes a cartridge filter with an ion exchange resin. Upon
long use of the humidifier without replacement of resin a white residue may
appear on the unit and objects next to it.
The white residue is calcium and magnesium comprised in the composition of
ordinary tap water. When the ion exchange resin in the filter expires, they are
released along with steam and settle on the surrounding objects and surfaces.
Though these substances are safe for people, in large amounts they may have
hazardous effect on furniture. By means of an ion exchange filter, installed at the
bottom of the tank, calcium and magnesium are removed from tap water. At the
beginning of operation the ion exchange filter can make water tea-colored. This
doesn t affect safety or operation of the unit.
To replace the filter it is necessary to remove a cap by turning it counterclockwise
and
then remove the filter also by turning it counterclockwise. The new filter is
installed in the reverse order. To purchase an ion exchange filter, please, contact
the seller.