10
11
If the TileVision
®
is used with a Sky™ receiver, the channel can be changed on the Sky™
receiver using the Sky™ remote control via the remote sensor on the TileVision
®
.
Note: A glass carrier/suction lifter is required when installing a TileVision
®
.
All connections should be made with the remote isolation switch for the TileVision
®
set to OFF.
Installing the TileVision
®
– Initial Connections
Sky™ Remote Control Link Setup
Preparation to use this facility should have been completed during
the installation of the first fix assembly (see page 7).
It is advisable to setup the Sky™ receiver so that it can be
controlled via the TileVision
®
before the TileVision
®
is installed. The
red LED on the TV Link (that is fixed to the TileVision
®
) will light
when correctly connected to and powered by the Sky™ receiver.
This is checked when connecting the aerial lead to the TileVision
®
.
The connection to the Antenna/RF connectors on the TileVision
®
and the Sky™ receiver must be made with both the TileVision
®
and
the Sky™ receiver disconnected from the mains supply. Use good
quality coax cable either directly from the RF2 outlet of the receiver
or the outlet of a Remote-Link amp in an uninterrupted run .
Once the connections have been made, the Sky™ receiver must be
setup to supply power to the RF 2 socket as detailed below.
To set-up the Sky™ receiver to work with the TileVision
®
the
Sky™ remote control must be used via the main TV (TV 1).
1
On the Sky™ remote control press
SERVICES
to show the
SERVICES menu.
2
Press the
4
button for the SYSTEM SETUP menu.
3
Press the
0
button, then the
1
button, then the
select
button, in
sequence, to display the INSTALLER SETUP menu.
4
Press the
4
button to select RF OUTLETS.
5
Press the
down
arrow to select RF Outlet Power Supply and
press the
left
or
right
arrows to change the setting to ON.
6
Press the
down
arrow to select Save New Settings and press
select
to save the settings.
7
Press the
sky
button to return to the previously viewed channel.
☛
Use the cable clips
provided to secure the
earth and speaker cables
to prevent them
obstructing the
TileVision
®
as it is fitted
into the back box.
S-232
RJ12
IR LINK
ANTENNA
INPUT
CVBS
IN
CI PORT
AUDIO
COMPONENT
S-VIDEO
IN
AUDIO L
PR
PC IN
OUT
OUT
IN
PB
Y
R
Red LED indicator
will light when power
is received from the
Sky™ RF2 outlet
Earthing Points
Introduce the lower
front edge of the unit
into the back box and
fit the earth cables to
the two earthing
screws as indicated
by the green labels on
the rear of the
TileVision
®
.
The earth cables are
electrical connections and
must not
be used to support the weight
of the TileVision
®
.
Power Socket
The Power connector is located at the extreme right of the
connection array.
Speaker Connections
The supplied stereo
speaker should be
connected after the
earthing straps are
connected to the rear
of the TileVision
®
as
detailed above.
The speaker terminals
on the TileVision
®
and on
the stereo speaker are marked with coloured dots which match the
colours of the supplied four-core speaker cable. To ensure that the
stereo speaker is connected correctly the individual leads should be
connected to their matching colours on both the TileVision
®
and the
stereo speaker.
The speaker connection block is found on the left of the rear of the
TileVision
®
. Lift one of the lugs, push one conductor of the speaker
lead into the connector, release the lug and give the lead a slight
pull to make sure that it is gripped correctly. The other wires should
be connected in the same way.
If two separate speakers and alternative speaker cables are being
used, the conductor with the stripe should be connected to the
negative terminal (L– or R–) and the plain conductor should be
connected to the corresponding positive terminal (L+ or R+). The
connections to the speakers terminals should be made in the same
way – striped conductor to the negative terminal and plain conductor
to the positive terminal.
Earth lead
connections
L–
L+
R+
R–
The speaker connection block
Sky™ digital receiver
RF 1
RF 2
TV 1
