background image

TECHNISONIC INDUSTRIES LIMITED 

 

 

RC-9100 Installation Instructions 

TiL 14RE508 Rev. B Issue 1 

12 

 
 
 
 
 
 
 

 

 

Technisonic Industries Limited 

240 Traders Blvd., Mississauga, ON Canada L4Z 1W7 

Tel: (905) 890-2113 Fax: (905) 890-5338 

 

IMPORTANT 

WARRANTY 

 
All  communication  equipment  manufactured  by  Technisonic  Industries  Limited  is 
warranted to be free of defects in Material or Workmanship under normal use for a period 
of one year from Date of Purchase by the end user. 
 
Warranty  will  only  apply  to  equipment  installed  by  a  factory  approved  and/or  authorized 
facility  in  accordance  with  Technisonic  published  installation  instructions.  Equipment 
falling under the following is not covered by warranty: 

 

Equipment that has been repaired or altered in any way as to affect performance, 

 

Equipment that has been subject to improper installation, 

 

Equipment that has been used for purposes other than intended, 

 

Equipment that has been involved in any accident, fire, flood, immersion, or subject to 
any other abuse. 

 
Expressly excluded from this warranty are changes or charges relating to the removal and 
re-installation  of  equipment  from  the  aircraft.  Technisonic  will  repair  or  replace  (at 
Technisonic's  discretion)  any  defective  transceiver  (or  part  thereof)  found  to  be  faulty 
during the Warranty Period. 
 
Faulty equipment must be returned to Technisonic (or its authorized Warranty Depot) with 
transportation charges prepaid. Repaired (or replacement) equipment  will  be returned  to 
the  customer  with  collect  freight  charges.  If  the  failure  of  a  transceiver  occurs  within  the 
first  30  days  of  service,  Technisonic  will  return  the  repaired  or  replacement  equipment 
prepaid. 
 
Technisonic  reserves  the  right  to  make  changes  in  design,  or  additions  to,  or 
improvements  in  its  products  without  obligation  to  install  such  additions  and 
improvements in equipment previously manufactured. This Warranty is in lieu of any and 
all  other  warranties  express  or  implied,  including  any  warranty  of  merchantability  or 
fitness, and of all other obligations or liabilities on the part of Technisonic. 
 
This  Warranty  shall  not  be  transferable  or  assignable  to  any  other  persons,  firms,  or 
corporations. 
 

For warranty registration, please complete the online 

Warranty Registration Form found at www.til.ca. 

 

 

 

Summary of Contents for RC-9100





















Reviews: