TigerStop TigerSaw 1000 Installation Manual Download Page 14 | Manualshive

Page: 14 / 68

background image

11

Unpacking Saw Body

Unpack the Saw Body

1. Remove the screws that hold the saw legs to the pallet.

Note: The saw body is designed to be lifted with a pallet jack or a fork lift. You can position the forks to pick up the saw body
from the side, as shown.

2.Insert the forks of the pallet jack or forklift under the saw body.

Note: Do NOT lift the saw body! The saw body must be secured BEFORE it’s
lifted.

3.Secure the saw body to ensure it will not tip over when lifted.

4.Lift the saw body and position the saw where it will be installed.

5.Before lowering the saw, insert the leveling feet as shown.

Table Installation

The table brackets and hardware will be inside the table accessory boxes. The table hardware will

be in hardware packs labeled “Feed Table Hardware”.

«
...
12
13
14
15
16
...
»

Summary of Contents for TigerSaw 1000





































































Reviews:

No comments

Related manuals for TigerSaw 1000

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Bacharach Pages: 2

Brand: p-light Pages: 28

The Wave Transformer

Brand: EarthQuaker Devices Pages: 21

Brand: J.P. SELECTA Pages: 32

Brand: Varimixer Pages: 28

Brand: EFX Pages: 2

Brand: Wacker Neuson Pages: 42

Brand: KERR Pages: 32

Brand: AVID LABS Pages: 20

Brand: Briteq Pages: 12

Brand: Crary Pages: 56

Brand: Osram Pages: 30

Spacelabs Medical 92506

Brand: OSI Systems Pages: 92

VL4000 BeamWash Luminaire

Brand: Vari Lite Pages: 190

Brand: York Fitness Pages: 18

Brand: 4B Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands