Tietzsch ProfiSafe LSP 4L User Instructions Download Page 18

6. Testing and charging the accu

In case the battery symbol appears when holding 
the test electrodes together, the accu needs to be 
recharged.
Therefore plug the test electrodes of the ProfiSafe 
into a 230 V socket, so that the display shows 230 V.
Complete recharge of the ProfiSafe takes at least 
10 hours.
In this context the on-time of about 30 seconds is 
irrelevant.
Again perform the function test before putting the 
instrument into operation (see section 3.1).

7. Maintenance
7.1 General information

The ProfiSafe is absolutely maintenance-free. Never-
theless, observe the following information in order to 
maintain safe operation:
Always keep the voltage tester dry and clean. The 
housing can be cleaned with a cloth dampened with 
isopropyl (alcohol) or soapy water.  

7.2  Repeated inspection

According to EN 61243-3 it is recommended to carry 
out repeated examinations.  
It should not exceed the time-limit of 6 years.  
Depending on operation conditions and frequency, a 
previous inspection may be recommendable. 
The serial number with the date of manufacturing 
(WWYYNN=

W

eek 

Y

ear 

N

umber) is imprinted on the 

backside of the device. Repeated inspections are 
offered by the manufacturer and  indicated by the 
inspection plate.

8.  Repair 

Repair is only allowed by the manufacturer or expli-

citly authorized repair shops.

In case of damages on the device or failure of the 

function test according to section 3.2 or for detailed 

inspection/calibration, please contact:  

[email protected]

 or send the device and a 

description of failure back to the manufacturer 

(address see page 1).

9. Limited warranty and limitation of liability

By continuous quality checks and production 

controls, most modern electronics and high quality 

materials we guarantee that the tester will be free 

from defects in material and workmanship for two 

years.

This warranty does not cover batteries, improper 

handling, not intended purpose, opening the hou-

sing, improper storage or damages from accidents.
No other warranties such as fitness for a particular 

purpose will be given.

We are not liable for any indirect, incidental or 

consequential damages or losses arising from any 

cause or theory.  

18

Summary of Contents for ProfiSafe LSP 4L





















Reviews: