INTRODUCTION
Introduction
Introduction.........................................................................................................................2
Parts Drawings........................................................................................................................3
W i n g … … … … … … … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . … … . … . . . … … . . . 4
Tail........................................................................................................................................5
Motor………...........................................................................................………….....……........6
Landing Gear………........................................................................................………….....……..7
Setup....................................................................................................................................8-10
.............................................................................................................................11
TABLE OF CONTENTS
A checklist is provided as below which will make shopping for these items easier.
OTHER ITEMS REQUIRED FOR ASSEMBLY
Adhesives:
You will need the
t h i c k i n s t a n t ( c y a n o a c r y l a t e )
adhesives.
Thank you for your purchase of the Thunder Tiger 3D Sukuoi EP. You can make t
proven 3D fun flyer
easily do any aerobatics and 3D maneuvers, includes Knife Edge, Hovering, Torque Rolls, Corbra...etc.
Made of Anti-Impact EPP material that reduce the crash damage. Very good for those who are interested in
learning 3D-aerobatics or experienced 3D pilots who are looking for a relaxed practicing plane that can be
used both outdoor and indoor.
3D Sukuoi EP
his
The
is designed for
intermediate pilot
minded
.
Before beginning the assembly read
the instructions thoroughly to give an understanding of the sequence of steps and a general awareness of
the recommended assembly procedures. Check the entire contents of your kit against the parts drawing
and photos to make sure that no parts are missing or damaged. This will also help you to become familiar
with each component of your plane. If you find that any of the parts are either missing or damaged, please
contact Thunder Tiger Distributors for Customer Service.
Radio:
A 4-channel radio with
3 micro servos and mini receiver
are required.
Battery:
Recommend the use
of a ACE Power Lipo battery
3S1P 1100mAh(No.2804).
Brushless Motor:
Recommend
OBL29/09-07A motor ( No.2354)
2
Paper Towel
Hobby Knife
Ruler
Pen, Pencil or Marker
Phillips&Flat Head Screw Drivers
Scissors
Nose Plier
Drill Bit 5/64” (2mm)
TOOLS AND SUPPLIES NEEDED
C o n t r o l l e r :
A C E B L C 1 2 A
(No. 8026) is a perfect controller
that controlling OBL motor
efficiently.
Extension Wire:
2 pieces of
extension wire in length of 9”.
Propeller:
There is 12” prop. in
the kit, yet it is only for test flight.
Recommended APC 10x4.7 SF
propeller for high performance 3D
aerobatics.
PARTS DRAWINGS
Open the box and check that you have all the parts as shown below.
3
Fuselage (1)
Glue (1)
Tail Gear (1)
AS6647 Fuselage
AS6648 Main Wing
AS6649 Tail
AS6653 11x8 SF Propeller
AS6652 Control Horn
No.2354 OBL 29/09-07A
Velcro B (1)
Firewall (1)
1.5 CFK Rod 390 (2)
5 11X8 Propeller (1)
Horizontal Tail (1)
Outrunner Brushless Motor 29/27-07A (1)
Aileron (L/1,R/1)
Wing (1)
AS6650 Pushrod
AS6651 Landing Gear
Vertical Fin (1)
Clevis (4)
Pushrod (4)
FRP Control Horn (4)
Reinforced Plate (1)
Superlite Wheel (2)
1.5 CFK Rod 98 (2)
1.5 CFK Rod 230 (2)
3x6mm Sink Screw (4)
Prop Nut (1)
Cross Mount (1)
Adaptor (1)
2x5mm Screw (3)
3x6mm Wood Screw (4)
2 CFK Rod 340 (1)
1.5 CFK Rod 180 (2)
Velcro A (1)
Hinge (8)
Hinge (4)
AS6336 Wheel
Landing Gear (2)
Wheel Colar (2)
Mount (2)
2.3x12mm Wood Screw (1)
