THUNDER TIGER Jackal 6544-F, Instruction Manual & Parts Catalogue

Page: 6 / 30

5
THE RC 2.4GHz SYSTEM
熟悉
2.4GHz
電控系統
5
Transmitter Antenna
發射機天線
Battery Level Indicator
發射機電源顯示燈
Power Switch
電源開關
Servo reversing switches
正逆轉設定裝置
Steering Trim
轉向微調鈕
Throttle Trim
油門微調鈕
Steering D/R (Dual Rates)
轉向大小動調整鈕
Throttle Trigger
油門控制板機
External Charging Jack
充電孔
2.4GHz Binding / LED
2.4GHz
校頻配對設定鈕
Steering Wheel
轉向舵輪
Battery Cover --
電池蓋
1
2
3
4
5
6
7
8
9
10
11
12
TRANSMITTER CONTROLS
1. Transmitter Antenna: Straighten up the antenna before operating the model.
2. Battery Level Indicator: Green / Red LEDs indicate the battery voltage. If the Red LED flashes, please replace the batteries.
3. Power Switch: Slide to turn the transmitter on or off.
4. Servo reversing switches: To reverse the servo's rotation direction at the flip of the switch. The reversing switches are
recessed into the transmitter to prevent accidental operation.
5. Steering Trim: Adjusts the steering in small increments or decrements to run the model straight.
6. Throttle Trim: Adjusts the throttle in small increments or decrements to shift the neutral position.
7. Steering D/R (Dual Rates): Turn this knob left or right to adjust the amount of the steering dual rate. Right to increase dual rate
amount and left to decrease the amount.
8. Throttle Trigger: Pull or push to control the movement of the model.
9. External Charging Jack: For rechargeable NiCd/NiHM battery pack on the transmitter only.
10. 2.4GHz Binding / LED: The Binding button is located on the top of the 2.4GHz transmitter. For additional details, please refer to
the “Binding” setting procedure (Page 6). LED indicate the RF status. The Red LED means RF funtion is not work.
11. Steering Wheel: Control the steering of the model.
12. Battery Cover: Slide cover to install or remove batteries.
1.
發射機天線 ：操作前直立發射機天線。
2.
發射機電源顯示燈 ：二顆
LED
設計顯示發射機電池殘量，若紅色
LED
燈閃爍時，請更換發射機電池。
3.
電源開關 ：發射機電源開關
4.
正逆轉設定裝置 ：依實際使用，控制伺服機作動方向。
5.
轉向微調鈕 ：利用此旋鈕，調整設定轉向正確中立點位置。
6.
油門微調鈕 ：利用此旋鈕，調整設定油門正確中立點位置。
7.
轉向大小動調整鈕 ：調整轉向伺服機的行程量。
8.
油門控制板機 ：控制車輛前進或後退的裝置
9.
充電孔 ：使用充電式電池時，可利用此充電孔，進行充電工作。
10.
2.4GHz
校頻配對設定鈕
：
2.4GHz
之
BINDING SW
校頻配對設定鈕，為配對發射
/
接收頻率之用。更多功能設定方式請參考說明
書第
6
頁“校頻配對步驟”。
11.
轉向舵輪 ：控制車輛轉向裝置
12.
電池護蓋 ：推移電池護蓋即可取出電池進行更換。
發射機各部功能簡介
10
5 7
2 2
6
12
9
3
8