THUNDER TIGER Jackal 6544-F, Instruction Manual & Parts Catalogue

Page: 10 / 30

9
11
ADJUSTING SLIPPER CLUTCH SYSTEM
限滑器(滑動離合器)
調整方式：螺帽旋入至最緊後，再鬆開約
1/4
圈。
注意：螺帽勿鎖入至最緊。當螺帽鎖入過多，將使扭力限制器無法在適當時機作動，造成傳動系統損壞。
tight the nut then loose 1/4 turn.
***Don't tight lock the nut, otherwise slipper clutch will not function and cause transmission easily be broken.***
Take off
拆下
a b
Loosen
Slipper
Clutch
鬆
Tighten
Slipper
Clutch
緊
c
The Jackal is equipped with an adjustable slipper clutch which is built into the large spur gear. The purpose of the slipper clutch is to
regulate the amount of power send to the wheels to prevent tire spin. When it slips, the slipper clutch makes a high-pitch, whining noise.
a. You can use 1.5mm hex. wrench to loose screw of gear cover.
b. Use the other 1.5mm hex. wrench to fix gear shaft.
c. Clockwise to tight slipper clutch, counterclockwise to loose it.
Jackal
於大主齒外側配備可調式限滑器，而限滑器
(Slipper clutch
也叫滑動離合器
)
，可以讓你調整從馬達傳遞到車輪的最大的扭力
，以適應低抓地力的路面。可避免車子在
瞬
間起動或加速時，因動力過大而產生的打滑現象。
a.
你可以使用隨車所
附
的
1.5mm
六角板手，鬆開左右兩個螺絲將齒輪蓋拆下。
b.
先使用一支
1.5mm
螺絲起子穿過驅動大齒輪軸使之無法旋轉。
c.
順時針方向為鎖緊限滑器，逆時針為鬆開限滑器。
FRONT TOE-IN / TOE-OUT
前輪束角調整
12
a. Use 4.0mm wrench to adjust front toe-in.
b. Lengthening the Turnbuckles will increase the amount of toe-in, shortening them will
increase the amount of toe-out.
c. The flange on the turnbuckle indicates the side that has the right-hand thread. Use it
as a guide to determine which way to turn the turnbuckle when adjusting its length.
a.
使用
4mm
扳手調整前輪束角。
b.
增長螺距將會增加內束角角度；縮短螺距將會增加外束角角度。
請參照本說明調整您愛車前輪的傾角。
FRONT CAMBER
前輪傾斜角調整
13
a. Use 4.0mm wrench to adjust front camber.
b. Lengthening tumbuckles can decrease front camber, shortening them will
increase front camber.
a.
使用
4mm
扳手調整前輪傾斜角（如圖示）。
b.
增長螺距將會減少傾斜角角度；縮短螺距將會增加傾斜角角度。
請參照本說明調整您愛車前輪的傾角。
Flange
凸緣向內
+
+
-
-
Flange
凸緣向內
+
+
-
-