background image

Fiber Coupled Laser Source

 

Chapter 6: Making the Safety Interlock Connections

 

Rev L, June 5, 2017 

Page 9

 

Chapter 6 

Making the Safety Interlock Connections 

The S3 series laser sources are equipped with a remote interlock connector located on the rear panel, see   

Figure 3

. All units have this feature regardless of their FDA and IEC classifications. In order to enable the laser 

source, a short circuit must be applied across the terminals of the Remote Interlock connector. In practice this 
connection is made available to allow the user to connect a remote actuated switch to the connector (i.e. an open 
door indicator). The switch (which must be normally open) has to be closed in order for the unit to be enabled. 
Once the switch is in an open state the laser source will automatically shut down. If the switch returns to a closed 
condition the laser source must be re-enabled at the unit by pressing the ENABLE switch. 

All units shipped from Thorlabs are configured with a shorting device installed in the Interlock connector. If you 
are not going to use this feature then you can leave the shorting device installed and the unit will operate normally 
as described in the procedures above. 

If you wish to make use of the Interlock feature you will need to acquire the appropriate connector mate and wire 
it your remote interlock switch. Next, remove the shorting device by pulling it out with a pair of needle nose pliers 
and install the connector into the interlock input. 

The interlock input only accepts a 2.5 mm mono phono jack. This connector is readily available at most 
electronics stores. 

The electrical specifications for the interlock input are shown in the following table. 

Specification 

Value 

Type of Mating Connector 

2.5 mm Mono Phono Jack 

Open Circuit Voltage 

+5 VDC with Respect to Chassis Ground 

Short Circuit Current 

0.5 mA DC 

Connector Polarity 

Tip is +5 V, Barrel is Ground 

Interlock Switch Requirements 

Must be N.O. Dry Contacts. 

Under no circumstances should any external voltages 

be applied to the Interlock input 

 

 

Figure 4 

Remote Interlock Connector 

 

 

Ground 

+5 Volts 

Summary of Contents for S3FC405



















Reviews: