manualshive.com logo in svg

THORLABS OTKB, Manual

Share
Download
THORLABS OTKB Manual Download Page 27

 

Optical Trap Kit 

 

19590-D04-V15; Apr 12, 2012 

Page 27 

www.thorlabs.com 

Part 11. 

Thorlabs Worldwide Contacts 

 

USA, Canada, and South America 

Thorlabs, Inc. 
435 Route 206 
Newton, NJ 07860 
USA 
Tel: 973-579-7227 
Fax: 973-300-3600 
www.thorlabs.com 
email: [email protected] 
 

 

Europe 

Thorlabs GmbH 
Hans-Böckler-Str. 6 
85221 Dachau 
Germany 
Tel: +49-(0)8131-5956-0 
Fax: +49-(0)8131-5956-99 
www.thorlabs.de 
email: [email protected] 
 

UK and Ireland 

Thorlabs LTD. 
1 Saint Thomas Place, Ely 
Cambridgeshire CB7 4EX 
Great Britain 
Tel: +44 (0)1353-654440 
Fax: +44 (0)1353-654444 
www.thorlabs.de 
email: [email protected] 

France 

Thorlabs SAS 
109, rue des Côtes 
78600 Maisons-Laffitte 
France 
Tel: +33 (0) 970 444 844 
Fax: +33 (0) 811 381 748 
www.thorlabs.de 
email: [email protected] 

Scandinavia 

Thorlabs Sweden AB 
Box 141 94 
400 20 Göteborg 
Sweden 
Tel: +46-31-733-30-00 
Fax: +46-31-703-40-45 
www.thorlabs.de 
email: [email protected] 
 

Japan 

Thorlabs Japan Inc. 
5-17-1, Ohtsuka 
Bunkyo-ku, Tokyo 112-0012 
Japan 
Tel: +81-3-5979-8889 
Fax: +81-3-5979-7285 
www.thorlabs.jp 
email: [email protected] 
 

China

 

Thorlabs China 
Oasis Middlering Centre 
3 Building 712 Room 
915 Zhen Bei Road 
Shanghai 
China 
Tel: +86 (0)21-32513486 
Fax: +86 (0)21-32513480 
www.thorlabs.com 
email: [email protected] 

 

Summary of Contents for OTKB





























Reviews:

No comments

Brands by name

Popular brands

Load more brands