THORLABS INT-POL-1300 Operation Manual Download Page 23

 

5

 Appendix

 

 

INT-POL-1300  

/ page 17 

5.4  Certifications and compliances 

Certifications and compliances 

Category 

Standards or description 

EC  Declaration 
of  Conformity  – 
EMC 

Meets  intent  of  Directive  2004/108/EC 

1

  for  Electromagnetic  Compatibility.  Compli-

ance was demonstrated to the following specifications as listed in the Official Journal 
of the European Communities: 

 

EN 61326-1:2006 
 

Electrical Equipment for Measurement, Control and Labora-
tory  Use  –  EMC  Requirements  –  Part  1:  General 
Requirements: 
Immunity: complies with basic immunity test requirements 

2

Emission: complies with EN 55011 Class B Limits 

2,3

 

IEC 61000-3-2 and IEC 61000-3-3. 

 

 

IEC 61000-4-2 

Electrostatic Discharge Immunity (Performance Criterion A) 

 

 

IEC 61000-4-3 

Radiated  RF  Electromagnetic  Field  Immunity  (Performance 
Criterion A) 

 

 

IEC 61000-4-4 

Electrical  Fast  Transient  /  Burst  Immunity  (Performance 
Criterion A) 

FCC  EMC  Com-
pliance 

Emissions comply with the Class B Limits of FCC Code of Federal Regulations 47, 
Part 15, Subpart B 

2,3

EC  Declaration 
of  Conformity  - 
Low Voltage 

Compliance was demonstrated to the following specification as listed in the Official 
Journal of the European Communities: 
Low Voltage Directive 2006/95/EC 

 

EN 61010-1:2001 

Safety 

Requirements 

for 

Electrical 

Equipment  for  Measurement,  Control,  
and  Laboratory  Use  –  Part  1:  General 
Requirements 
 

U.S.  Nationally 
Recognized 
Testing  Labora-
tory Listing 

UL 61010-1 2

nd

 ed. 

ISA-82.02.01 2

nd

 ed. 

Canadian  Certi-
fication 

CAN/CSA C22.2 No. 61010-1 2

nd

 ed. 

Additional  Com-
pliance 

IEC 61010-1:2001 

Equipment Type 

Test and measuring 

Safety Class 

Class I equipment (as defined in IEC 60950-1:2001) 

1

 Replaces 89/336/EEC.

 

2

 Compliance demonstrated using high-quality shielded interface cables shorter than or equal to 3 me-

ters. 

3

 Emissions, which exceed the levels required by these standards, may occur when this equipment is  

connected to a test object. 

4

 

Replaces

 

73/23/EEC, amended by 93/68/EEC. 

Summary of Contents for INT-POL-1300





























Reviews: