manualshive.com logo in svg

THORLABS ELLB, Original Instructions Manual, Page: 9 / 14

Share
Download
THORLABS ELLB Original Instructions Manual Download Page 9

ELLB Distribution Board for Resonant Piezo Motor Products

 

Chapter 3: Operation

 

Rev C Jan 2020 

Page 7

 

3.3. 

Controlling the Stage 

The stage can be controlled by the Elliptec software running on a PC, or by writing a custom application using 
the messages described in the communications protocol document. The modes of control are described in the 
following sections. 

 

Caution 

Moves cannot be initiated using the FW, BW and JOG buttons on the interface board.  

 

3.3.1.  Software Control 

 

Caution 

If multiple modules are connected, ensure that the address of each modue has been changed (see section 
3.2.4) before using the software. 

 
When connected to the host PC, the stage can be controlled remotely, via the Elliptec software. 
 

1.  Download the Elliptic software from the downloads section at www.thorlabs.com. Double click the 

saved .exe file and follow the on-screen instructions. 

2.  Connect the hand-held controller to the stage unit. 
3.  Connect the hand-held controller to the 5V Power Supply and switch on. 
4.  Connect the hand-held controller to the PC USB port and wait for the drivers to be installed. 
5.  Run the Elliptec software. 

 

 

6.  In the top left of the GUI panel displayed, select the COM port to which the device is connected, and 

click ‘Connect’. The software will search the comms bus and enumerate the device. 

7.  Click the Home Offset ‘Get’ button, then click ‘Home’ to home the stage. 
8.  The GUI and device are now ready for use. See the helpfile supplied with the software for more 

information. 

Summary of Contents for ELLB















Reviews:

No comments