THORLABS ELL14 Operating Manual Download Page 21

ELL14 Motorized SM1 Optic Rotator

 

Chapter 8: Thorlabs Worldwide Contacts 

Rev. B, Feb 2020 

 

Page 19

 

Chapter 8 

Thorlabs Worldwide Contacts 

For technical support or sales inquiries, please visit us at 

www.thorlabs.com/contact

 for our most up-to-date contact 

information.  

 

 

 

 

 

 

 

 

 

 

 

 

Thorlabs verifies our compliance with the  WEEE (Waste Electrical and Electronic Equipment) directive of the 
European Community and the corresponding national laws. Accordingly, all end users in the EC may return “end 
of life” Annex I category electrical and electronic equipment sold after August 13, 2005 to  Thorlabs, without 
incurring disposal charges. Eligible units are marked with the crossed out “wheelie bin” logo (see right), were sold 
to and are currently owned by a company or institute within the EC, and are not dissembled or contaminated. 
Contact Thorlabs for more information.  Waste treatment is your own responsibility.  “End of life” units must be 
returned to Thorlabs or handed to a company specializing in waste recovery. Do not dispose of the unit in a litter 
bin or at a public waste disposal site.

 

 

 
USA, Canada, and South America 

 

Thorlabs, Inc.  
[email protected]  
[email protected]  
 

 
UK and Ireland 

 

Thorlabs Ltd.   
[email protected]  
[email protected]  

Europe 

 

Thorlabs GmbH  
[email protected]

 

 

 

Scandinavia 

 

Thorlabs Sweden AB  
[email protected]  

France 

 

Thorlabs SAS  
[email protected]

 

 

 

Brazil 

 

Thorlabs Vendas de Fotônicos Ltda.  
[email protected]  

Japan 

 

Thorlabs Japan, Inc.  
[email protected]  

China 

 

Thorlabs China  
[email protected]  

Annex I 

Summary of Contents for ELL14























Reviews: