Thor Kitchen TWC2403DI Service Manual Download Page 25

 

 

 

Maintenance Service and Trouble Shooting   

position is to be used for fast freezing or continuous running, its temperature for power 
off is too low, therefore, the compressor won't stop and the temperature in the 
refrigerator becomes lower and lower. 
 
b) Inspection method: check the temperature control knob to see whether it is set in the 
position "coldest". 
 
2) Thermostat is malfunctioning and makes the compressor running continuously 
Analysis of Trouble 
When the thermostat doesn't work normally, it will make the compressor run 
continuously, and hence very low temperature will be achieved in the refrigerator. The 
fault is generally due to the fact that the contacts of the thermostat cannot be released. 
 
Remedy 
Dismantle the thermostat and make a through checkup, if it is totally out of functioning, 
replace it with a new one. 
 
3) Evaporation temperature is too high in refrigerating system, resulting in lower 
refrigerating capacity and hence continuous running of compressor 
 
Analysis of Trouble 
Leakage of refrigerant and clogging in a refrigerating system will directly affect its 
refrigerating capacity. Due to the reduction in its refrigerating capacity, the refrigerator 
temperature cannot reach its rated value, the thermostat won't work, thus the 
compressor runs continuously. When the evaporation temperature in the system is too 
high, the temperature sensing agent in the temperature sensor is also hotter, therefore, 
the thermostat is unable to cut off the power supply to the compressor and stop it. 
 
Remedy 
If it has been found that the refrigerant in the system is insufficient in quantity, recharge 
it with refrigerant. In case clogging occurs, disassemble the part where it is blocked. If 
the evaporation temperature is too high, settle this problem with an appropriate 
quantity of refrigerant. 
 
4) No stoppage of compressor due to damaged heat-insulation layer inside case body 
and/or door seal 
Analysis of Trouble 
When the heat-insulation layer inside the case body deteriorates or the door seal is not 
closely touches the door frame, the temperature in the refrigerator will rise and makes 
the compressor running continuously. 
 
Remedy 
Check the heat-insulation layer for its damaged parts, repair it to improve its 
heat-insulation property. If the door has deformed or the door seal is not tightly sealed 
against the case body, repair them, respectively. 
 
5) Too much food is placed in the refrigerator, or is placed too densely, resulting in poor 
ventilation or poor conditions for temperature sensing, and hence no stoppage of the 
compressor. 

26 

Summary of Contents for TWC2403DI




























Reviews: