manualshive.com logo in svg

THOMSON TS 840, Service Manual

Share
Download
THOMSON TS 840 Service Manual Download Page 39

APPENDIX “A” 

 

THOMSON TECHNOLOGY

©

 

 

 

TYPICAL AUTOMATIC TRANSFER SWITCH 

COMMISSIONING PROCEDURES  

Model Series TS 840

 

 

9087A - 198

th

 Street, Langley, B.C. Canada V1M 3B1 

•

 Telephone (604) 888-0110 

•

 Telefax (604) 888-3370

 

Note

: The following commissioning procedures are provided for general 

information only pertaining to typical site installations and applications.  
Contact the equipment supplier for further information as may be required. 

DANGER!!!! 

Arc Flash and Shock Hazard. Will cause severe injury or death. 

 

Do not open equipment until ALL power sources are disconnected 

 

This equipment must be installed and serviced only by qualified electrical 

personnel utilizing safe work practices and appropriate Personal Protective 

Equipment (PPE). Failure to do so may cause personal injury or death 

 

 
 

CAUTION 

Commissioning procedures must be performed by qualified personnel only.   
 
 

Ensure the Automatic Transfer Switch (ATS) Control Isolation Plug is 
disconnected prior to energizing the supply sources.  Manually place the transfer 
switch mechanism in the neutral position by inserting the manual operating 
handle into the mechanism and turning until the neutral postion has been reached 
as is indicated on the transfer mechanism. 

 

NOTE: An optional hand held, plug-in Service Display Module (SDM) is available 
for the TSC 80 Transfer Controller.  The SDM module provides an LCD screen to 
display additional detailed information on the operation and settings of the TSC 
80 controller for simplified servicing/trouble shooting procedures. For detailed 
information, refer to the separate SDM module instruction manual (PM065).

 

Pre-Commissioning Checks Prior to Commissioning Agent On-Site (to 
allow loads to be supplied prior to final commissioning) 

1)  Verify the system voltage of both sources (i.e. generator and utility) to be applied 

to the transfer switch are of the correct nominal system value which matches the 
ATS drawings and the ATS equipment label ratings. If system voltage is incorrect 
for the rating of the ATS supplied contact Thomson Technology. 

CAUTION

: 

FAILURE TO RE-CONFIGURE ATS VOLTAGE TO MATCH SYSTEM 

VOLTAGE WILL RESULT IN EQUIPMENT MALFUNCTION AND DAMAGE. 

 

2)   For 240V High Leg Delta systems refer to the ATS instruction manual for correct 

phasing required and re-configuring procedures. 

Summary of Contents for TS 840












































Reviews:

No comments

Brands by name

Popular brands

Load more brands