7
Connections and Set-up
EN
Programming the remote control
Automatic code search
This method can be used to automatically find the most
appropriate code for your appliance.
1.
Switch on the appliance you wish to use the remote control
with.
2.
Press the relevant button for this appliance on the remote
control, and while holding this button down, press the
standby button until the light or the appliance buttons of the
remote control come on. Release both buttons.
3.
Point the remote control at the appliance and press
PLAY
.
Wait until the light stops flashing. If the appliance has not gone
into standby mode, press the
PLAY
button again to continue
the search for the next set of codes. Repeat this operation
until the appliance goes into standby mode.There are around
20 sets of codes.
4.
When the appliance goes into standby mode, switch it on again
without using the remote control. Press the
REV
button as
many times as is required to return the appliance to standby
mode.
5.
Press the
STOP
button and hold it down until the light or the
appliance buttons of the remote control go off.
Note:You can cancel the programming operation at any time by
pressing the
EXIT
button.
Manual programming
This method involves carrying out a manual search for the codes
to be used for controlling your other appliances.
1.
Switch on the appliance you wish to use the remote control
with.
2.
Press the relevant button for this appliance on the remote
control, and while holding this button down, enter one of the
codes relevant to your make of appliance (there is a list of
codes at the end of this manual). If the light or the appliance
buttons of the remote control flash you have entered the
wrong code or it is not possible to program the remote
control.
3.
Point the remote control at the appliance and press the
relevant button (
VCR
,
DVD
, etc). Press the
standby button.
If the appliance does not go into standby mode, try another
code.
Depending on the year of manufacture and the type of appliance,
some functions may not be available. Certain codes may cover
more functions than others.Test the functions you can control and,
if appropriate, try other codes.
Note here the
code(s) which work
best.
When you change the remote control’s batteries, remember to
reprogram it.
Programming the volume control function
If you have programmed the TV remote control to use with other
appliances and these are connected to an amplifier you can also
programme the remote control to adjust the volume when you are
using one of these appliances.The example below describes the
procedure for programming a DVD player.
1.
Programme the
AMP
button on the remote control to use
with the amplifier (refer to page 6).
2.
Move the remote control away from the appliances. Press the
-
button and while holding it down, press the relevant
mode button (
DVD
, in this example), then the
AMP
button.
Release the
-
button.
3.
Switch on the amplifier, then the DVD player.
4.
Set the remote control to
DVD
, play a disc and adjust the
volume using the
+/-
buttons.
Repeat this operation for the other appliances.
To cancel the programmed function for any of the appliances, press
the
-
button, while holding it down and enter the code 000
using the numeric buttons.
Video recorder
DVD player
Satellite receiver
Hi-fi system
Press the
VCR
button
Press the
DVD
button
Press the
SAT
button
Press the
AMP
button
On/Standby
On/Standby
On/Standby
On/Standby
MENU
To display the main menu
To display the main menu
To display the main menu
Vertical scrolling in menus
Vertical scrolling in menus
Vertical scrolling in menus
Horizontal scrolling
Horizontal scrolling
Horizontal scrolling
in menus
in menus
in menus
OK
To confirm an action
To confirm an action
To confirm an action
EXIT
To close a menu
To close a menu
To close a menu
0-9
To directly access channels
To enter numeric values
To directly access channels
To select a station using
or enter numeric values
or select options in menus
or enter numeric values
its number
PR+/PR-
To change channels
To change chapters
To change channels
To change stations
AV
To select av input
To select av input
REV
Rewind
Rewind
PLAY
Play
Play
FWD
Fast forward
Fast forward
STOP
Stop
Stop
PAUSE
Pause picture
Pause picture
REC
Record
To switch the sound off and
back on again
+/-
To set the volume level
VCR
DVD
SAT
AUX
AMP
42PB120S5-EN2 22/03/05 15:37 Page 7
