background image

 

 

 

 

WARNING! 

Any damages caused by using incorrect RS232 cable will be 
outside of our warranty scope. If you are not sure which one 
is correct RS232 cable, please purchase the correct RS232 
cable from us directly.   

 

2-2-4  Connect chassis ground terminal to earth or to vehicle chassis using # 8 AWG wire. 

 

WARNING! 

Operation of the inverter without a proper ground, connection 
may result in an electrical safety hazard. 

 

 

WARNING! 

Shock Hazard. Before proceeding further, carefully check the 
inverter is NOT connected to any batteries, and that all wiring 
is  disconnected  from  any  electrical  sources.  Do  not  connect 
the output terminals of the inverter to an incoming AC source. 

 
2-3  Installation: 

Where to install

Ǻ

 

The power inverter should be installed in a location that meets the following requirements. 

2-3-1  Dry 

 Do not allow water to drip or splash on the inverter. 

 
2-3-2  Cool 

 Ambient air temperature should be between -20°C and 50°C, the cooler the better. 

 

2-3-3  Safe 

 Do not install in a battery compartment or other areas where flammable fumes may 

exist, such as fuel storage areas or engine compartments. 

 

2-3-4  Ventilated 

 Allow at least 3 inch of clearance around the inverter for airflow. Ensure the 

ventilation openings on the rear and bottom of the unit are not obstructed. 

 

2-3-5  Dust-free 

  Do  not  install  the  inverter  in  a  dusty  environments  where  are  dust,  wood 

particles or other filings/shavings. 
These dusts can be pulled into the unit when the cooling fan is operating. 
 

2-3-6  Close  to  batteries 

  Avoid  excessive  cable  lengths  but  do  not  install  the  inverter  in  the 

same compartment as batteries. 
Use the recommended wire lengths and sizes (see section 2-6). 
Also  do  not  mount  the  inverter  where  it  will  be  exposed  to  the  gases  produced  by  the 
battery.  These  gases  are  very  corrosive  and  prolonged  exposure  that  will  damage  the 
inverter. 

YOUR CONNECTION TO SAFETY

Thiele KG 

• V
orderer W

einberg 26 • D-71522 Backnang • T

el.: +49 (0)7191 3560-0 

• Fax.: +49 (0)7191 3560-19 

[email protected] 

• www

.thiele-kg.de

Thiele KG 

• V

orderer W

einberg 26 • D-71522 Backnang • T

el.: +49 (0)7191 3560-0 

• Fax.: +49 (0)7191 3560-19 

[email protected] 

• www

.thiele-kg.de

YOUR CONNECTION TO SAFETY

klick to

www

u-s-v

YOUR CONNECTION TO SAFETY

klick to

www

ACDC-DCDC

YOUR CONNECTION TO SAFETY

klick to

www

SYSTEME

YOUR CONNECTION TO SAFETY

klick to

www

CONTACT

YOUR CONNECTION TO SAFETY

klick to

www

CALLBACK

Summary of Contents for Asian Electron PSW1500W Series




















Reviews: