Thiel SmartSub SS1, Owner'S Information

Page: 6 / 16

LEFT
RIGHT CENTER
L REAR R REAR
SUB
LFE
Level
Rear Wall
Distance
Side Wall
Distance
LFE Output
LFE Input
Normal
Input
Normal
Output
Trigger
On
Off
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN AVIS:
RISQUE DE CHOC ELECTR IQUE - NE PAS OUVRIR
!
THIEL SmartSub
®
Model
Ser N o
Voltage
THIEL Audio • 1026 N
andino Boulevard • Lex
ington, Kentucky USA
• www.thielaudio.co
m
On
Auto
Flush Off
1.5
0.5 1.0
0
0 Off
2.0
2.0
2.5
1.0 1.5
0.5
100
60
70
80
90
50
On
Replace fuse only
with same rating.
Remplacer le fusible p
ar un autre de la meme valeur
. Fuse
T6.3A L 250V for 120v
T3.15A L 250V for 240
v
®
C US
U.S. patent 6,801,628
other patents pending
120V~ 6.3A 60Hz or
230V~ 3.15A 50Hz
Right Bal Input
Left Bal Input
L +
L –
R – R +
INPUT
OUTPUT
Power Amplifier
for main speakers
Preamp or Processor
SmartSub
Passive
Crossover
Left/Right
outputs
Sub
output
Main Left/Right speakers
Subwoofer
PowerPoint
PowerPlane
THIEL Audio • Lexingto n, KY • USA
www.thielaudio.com
Output to Subwoofer
Left channel speaker lev
el input
Right channel speaker
level input
This unit matches
speaker model
+ –
+
–
Model PXO2
s/n
LFE Configuration
System Configurations
6
In this configuration the subwoofer is used only for reproduction of
the ‘point one’ subwoofer channel and is driven by the processor’s
subwoofer output connected to the subwoofer’s LFE input.
This configuration is a good choice when the main speakers play
sufficiently loud and their bass is satisfactory for applications other
than movie effects.
Passive Crossover Configuration
This configuration has connections and benefits identical to the
following one except the passive crossover provides no adjustments
and is available for only selected THIEL model main speakers.
Tell the processor the main speakers are large, even if they are not.
The SmartSubs can be used in four ways depending on
your requirements:
1. As a stand-alone unit.
2. With a passive crossover.
3. With the SmartSub Integrator in augment mode.
4. With the SmartSub Integrator in crossover mode.
The configuration chosen will determine your required
equipment, hookup connections and processor settings.
Which system configuration is best for you depends mainly
on the capabilities of your main left/right speakers.
Additional discussion of these options can be found in
the section Crossover Use . In addition, there is a
comprehensive flow chart for your reference on pages 12 and
13 that guides you through all aspects of system
configuration, hookup, and adjustment. More information
on Integrator hookup and adjustment can be found in that
product’s manual.
1
If your main speakers play sufficiently loudly for all
your uses and they reproduce the bass with satisfying
completeness, then the subwoofer is only needed to
reproduce the LFE (low frequency effects, or subwoofer)
channel and it can be used in the LFE configuration without
a crossover or Integrator.
If your main speakers play sufficiently loudly for all your
uses but do not reproduce the full low frequency range of the
left/right channels, you should also use the subwoofer to
augment the bass response of your main speakers. This can
be accomplished without altering the signal or wiring to your
main speakers by using one of the next two configurations.
2
A SmartSub Passive crossover can be used if one is
available to match your main THIEL speakers and if low
frequency adjustments are not required.
A two-channel crossover is illustrated but a five-channel
unit is also available to allow the subwoofer to augment the
bass of five channels.
LEFT
RIGHT CENTER
L REAR
R REAR
SUB
Right Bal Input
Left Bal Input
L +
L –
R –
R +
INPUT
OUTPUT
Power Amplifier
for main speakers
Preamp or Processor
Left/Right
outputs
Sub
output
Main Left/Right speakers
Subwoofer
LFE
Level
Rear Wall
Distance
Side Wall
Distance
LFE Output
LFE Input Normal
Input
Normal
Output
Trigger
On
Off
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTR
IQUE - NE PAS OUVRIR
!
THIEL SmartSub
®
Model
Ser N o
Voltage
THIEL Audio • 1026
Nandino Boulevard • Lexin
gton, Kentucky USA
• www.thielaudio.com
On
Auto
Flush Off
1.5
0.5
1.0
0
0 Off
2.0
2.0
2.5
1.0
1.5
0.5
100
60
70
80
90
50
On
Replace fuse only
with same rating.
Remplacer le fusible p
ar un autre de la meme valeur
.
Fuse
T6.3A L 250V for 120v
T3.15A L 250V for 240
v
®
C US
U.S. patent 6,801,628
other patents pending
120V~ 6.3A 60Hz or
230V~ 3.15A 50Hz