Manuale d'installazione, uso e manutenzione
PKOKKOLAPLUS – PMOODPLUS
V
W
XYH
FN
K OH
JGGQ LJ MRH
7.1 DESCRIPTION OF THE OPERATING STAGES
START:
has a duration of approx. 20 minutes, during this phase the appliance is programmed to light the flame. The appliance will
not accept power variations in the firebox. If the appliance does not start up correctly it could be due to one of the following factors:
cleanliness of the generator, smoke exhaust particularly cold, sudden surges and drops in the electric power supply, fuel is too
moist or does not comply with the specifications (see para. 3.2) .
WORK:
the appliance works according to the combustion and ventilation power set by the user. The spark plug is dead.
OFF:
has a duration of approx. 25 minutes. In this phase the appliance is switched off until a new "on" phase is initiated. The aim is
to make the pellet embers in the brazier die out and cool the appliance. The room fan and the smoke suction unit continue to
operate as required. In any case after approx. 25 minutes the appliance goes into stand-by mode.
7.2 SWITCHING ON THE STOVE
Before using the appliance check that all the movable parts are correctly fitted. Also remove any labels and stickers
from the glass to avoid that permanent traces remain on the surfaces. Verify that the electric connections have been
made perfectly. Check also that the firebox door is firmly closed.
Z[\
]^[
_`
a^`bc
d
ef
`g
[
f^
]hei
`
ig[
ij
`
ga`
`g[
k
lah
[
b
_
i]^^[
i`l
m
f]
_b`
b]c
[h
b
c
`g[
k^a
n
b[^
ac
h
`a
j[
ia^[
`]
b
c_[^
`
`g
[
`
[[`g
]
\
`g
[
kl
ah[
bc
`
g[
g
]l[
_
f^]ob
h[h
bc
`
g[
k^
an
b[^p
Then carry out the following operations:
1) Power up the appliance and turn the I/0 switch to position “I”.
2) Ensure that the appliance is connected to the smoke exhaust: we recommend against using aluminium tubes and we
recommend always using sealing gaskets. Further information is given in paragraph dedicated to the smoke discharge of
this use and maintenance booklet.
3) Load the pellets into the hopper.
4) Press the
Flame Button
to begin the start up phase and the word
START
will appear on the display.
Press the
Flame Button
repeatedly to set the desired combustion power which will only activate at the end of the START cycle
which takes roughly 20 minutes.
In this stage any level of combustion power set by the user is ignored to meet the correct power values set by the manufacturer.
Press the
Ventilation button
repeatedly to set the six fan speeds; the fan will only activate once the smoke has reached the preset
temperature.
The electrical heater will start to overheat and only after a few minutes the first lot of pellets will start dropping into the brazier. This
occurs because the screw feeder has to fill up because it is completely empty. At the first start up the appliance may require the
starting sequence to be performed twice for the reason explained above: before starting up the second time empty and vacuum out
the brazier.
ATTENTION: During the START sequence the appliance ignores all the commands that are transmitted or set. Once
this phase has ended the word WORK appears on the display.
When the machine is in the running phase the combustion can be changed manually.
ATTENTION: If the appliance does not start up correctly check that the brazier and electric heater are clean. It is very
important to ensure that the tube lodging of the electric heater is clean; there must be no deposits or dust. It is
recommended to use an efficient ash vacuum cleaner but only when the appliance has cooled down.
7.3 COMBUSTION AND VENTILATION ADJUSTMENTS
Set the combustion power of the stove by acting on the
Flamebutton
or on the supplied infrared remote control. The combustion
power regulates the pellet drop. The selected combustion power level will appear on the display.
Set the ventilation speed of the stove by acting on the
Ventilation Button
or use the supplied infrared remote control. The
ventilation speed regulates the number of fan revolutions. A slight vibration of the stove is quite normal when it is running. The
selected ventilation power level will appear on the display.
7.4 INFRARED REMOTE CONTROL
A practical infrared remote control is supplied with the appliance: act on the blue button to regulate the ventilation power, act on the
grey button to start up, adjust the combustion power and shut off the appliance.
7.5 CHANNELLING
Summary of Contents for KOKKOLA
