background image

pag. 19

INSTALLATION

Press the               button and/or the button               to set the hour for the appliance to stop for the first time during the day 

on Monday (e.g. 11.00 am). Then press the               button to confirm. The following graphic image will appear on the 

display:

Press the               button and/or the               button to set the minutes next to the hour for the appliance to stop for the first 

time during the day on Monday (e.g. 11.30 am). Then press the               button to confirm. The following graphic image 

will appear on the display:

Now press the               button and activate the programming mode (        symbol indicates programming mode is active) for 

the first on-off phase for Monday. 

CAUTION:  for the programming to be active the 2 symbols        must appear.   Then press the               button to quit the 

menu relevant to the first programming for Monday.

The following graphic image will appear on the display:

If you do not enter a value        next to OFF1 11.30, the OFF value from another subsequent day will be adopted and the 

        symbol activated.

The second on-off programming for Monday must be made in the same way as the first on-off programming for Monday. 

Program the appliance on-off settings for each day of the week following this procedure.

If you do not want to program the appliance for a particular day, such as for example Thursday, then the display for the two 

programmings for Thursday should appear as shown below; that is the        symbols should not appear on the display.

Summary of Contents for Ecotherm Compact





































Reviews: