Thermo NanoDrop One User Manual Download Page 188

Page: 188 / 312

Learning Center

Set Up the Instrument

188

NanoDrop One User Guide

Thermo Scientific

Select location for saving collected data

–

from instrument Home screen, tap

Connectivity Status

icon

–

the Data Storage message box is displayed as in the example below

–

select an available option below:

• to store all subsequently acquired measurement results only in the

NanoDrop One database on the instrument, set Data Storage to

Local

(see

example above).

• to store all subsequently acquired measurement results in the NanoDrop One

Viewer database on a computer connected to the instrument with an Ethernet
cable, set Data Storage to

Direct-Connect PC*

(see

Set Up Ethernet Connection

for details).

• to store all subsequently acquired measurement results in the NanoDrop One

Viewer database on a computer connected to the instrument through a wireless
network, set Data Storage to the

computer’s assigned name*

(see

Set Up Wi-Fi

Connections

for details).

The Ethernet and wireless options listed above will also store data on the

instrument as a backup.

Note

The Connectivity Status icon is active, i.e., blue, only when the instrument

is connected to a personal computer (PC) with an

Ethernet cable

or through a

properly configured wireless network, as in the example below.

Current location for
storing collected data

Connectivity status icon

Summary of Contents for NanoDrop One
























































































































































































































































































































Search results

Summary of Contents for NanoDrop One

Reviews:

Thermo NanoDrop One, User Manual, Page: 188 / 312

Search results

Summary of Contents for NanoDrop One

Reviews: