manualshive.com logo in svg

Thermo NanoDrop One, User Manual, Page: 184 / 312

Share
Download
Thermo NanoDrop One User Manual Download Page 184

3

 Learning Center

Set Up the Instrument

184

NanoDrop One User Guide

Thermo Scientific

Set up Wireless Connections

Use Wi-Fi™ to connect the instrument to a remote computer through a wireless local area 
network (WLAN). The remote computer can then be used to store or view data acquired with 
a NanoDrop One instrument.

Select Wi-Fi network on the instrument

–

from instrument Home screen, tap 

 (Settings)

–

tap 

System 

tab

–

tap 

Wi-Fi (

if Wi-Fi is disabled, button in upper right is set to “OFF” and no wireless 

networks are listed)

–

tap button to enable Wi-Fi and display available Wi-Fi networks

–

select remote computer’s Wi-Fi network host and tap 

Connect 

(here is an example)

Note  

To 

store or view collected data on a connected computer

 using W-Fi, 

NanoDrop One Viewer software must be installed on the remote computer and the 
computer must be configured for Wi-Fi data storage. The instrument must also be 
connected to the remote computer’s network host and have Wi-Fi enabled.

Summary of Contents for NanoDrop One

























































































































































































































































































































Reviews:

No comments