manualshive.com logo in svg

Thermo NanoDrop One, User Manual, Page: 183 / 312

Share
Download
Thermo NanoDrop One User Manual Download Page 183

 

3 

Learning Center

Set Up the Instrument

Thermo Scientific

NanoDrop One User Guide

183

–

tap 

Unpair

device is no longer listed under “Paired Devices” but remains in Available Devices list

–

tap 

Back 

to return to System settings

–

tap 

Done

 to close Settings

Set up Ethernet Connection

The instrument Ethernet port can be used to set up a wired connection between the 
instrument and a personal computer (or PC). The connected computer can then be used to 
store or view data acquired with the NanoDrop One instrument. (

NanoDrop One 

Viewer software

 must be installed on the computer.)

Tools needed:

• Standard (straight through) Ethernet cable (CAT5e or newer is recommended)

Set up Ethernet connection

–

connect Ethernet cable between Ethernet port on instrument back panel (see image 
above) and Ethernet port on computer

Note  

If the computer is an older model, you may need a crossover Ethernet cable instead. 

Most newer model computers are designed to automatically detect and work with both 
cable types. However, a straight through cable will provide best performance.

Summary of Contents for NanoDrop One

























































































































































































































































































































Reviews:

No comments