Thermo Scientific GENESYS 10S Vis User Manual Download Page 61

Page: 61 / 134

Thermo Scientific

GENESYS 10S Vis User Guide

Concentration Measurements—Advanced A-%T-C

Use the Advanced A-%T-C application for concentration measurements for:

• Selecting a measurement mode (concentration with one standard or concentration with a

factor).

•

Recalling a Test

•

Setting Up Test Parameters

•

Measuring a Standard

Entering a Factor

(only if you select either concentration with

one standard or concentration with a factor)

•

Measuring a Blank

•

Measuring Samples

To get started, press

Test

, highlight

Advanced A-%T-C

and press

Enter

Recalling a Test

To recall a test

1. Press

Stored Tests

2. Highlight the test and press

Enter

Load Test

to display the parameters for the selected

test.

Summary of Contents for GENESYS 10S Vis







































































































































Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands

Thermo Scientific GENESYS 10S Vis, User Manual

Search results

Summary of Contents for GENESYS 10S Vis

Reviews:

Related manuals for GENESYS 10S Vis

Brands by name

Popular brands