Thermo Scientific EASY-Spray NG User Manual Download Page 33 | Manualshive

Page: 33 / 62

background image

Thermo Scientific

EASY-Spray Series Ion Source User Guide

19

4

Connecting the EASY-Spray Column Plumbing

To connect the plumbing from the Thermo Scientific LC instrument to the EASY-Spray
column, follow these topics.

Contents

• Tools and Supplies

• Installing the EASY-Spray Column for the First Time

• Setting the Column Temperature

• Using the nanoViper Fitting

• Examples of LC Connections to the EASY-Spray Column

• Additional Resources

Tools and Supplies

lists the required tools and supplies for configuring the LC plumbing and EASY-Spray

column connections. Not all parts are required.

Note

The kit for the EASY-Spray Series ion source supplies the venting Tee, fittings, and

sleeves only. You are responsible for supplying the remaining parts and tools.

Table 4.

Tools and supplies (Sheet 1 of 2)

Image

Description

Part number

One- and two-column setups

A/B mixing/venting Tee, stainless
steel, with three attached ferrules
and nuts

SC901

«
...
31
32
33
34
35
...
»

Summary of Contents for EASY-Spray NG































































Reviews:

No comments

Related manuals for EASY-Spray NG

Brand: B&K Pages: 12

SafetuNet Alert

Brand: Masimo Pages: 2

Brand: SAMCHULLY Pages: 48

Brand: Gallagher Pages: 6

Brand: DBX Bushido Pages: 12

Brand: unios Pages: 2

Brand: P.Lindberg Pages: 76

Brand: Waters Pages: 4

Brand: Waterpik Pages: 2

Brand: Vaisala Pages: 2

Brand: Lalizas Pages: 12

BOBCAT 130 Series

Brand: Balcrank Pages: 12

Brand: E-FLOR Pages: 124

Brand: Elenco Electronics Pages: 12

Brand: GRAVITY Pages: 2

Brand: Petromax Pages: 16

Brand: SereneLife Pages: 4

Brand: Richiger Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands