manualshive.com logo in svg

Thermo Scientific EASY-Spray NG, User Manual, Page: 35 / 62

Share
Download
Thermo Scientific EASY-Spray NG User Manual Download Page 35

 

4 

Connecting the EASY-Spray Column Plumbing

Setting the Column Temperature

Thermo Scientific

EASY-Spray Series Ion Source User Guide

21

To install the EASY-Spray column

1. (Optional) Follow the procedure 

To install the optional Tee holder under the column 

holder

. 

2. Follow the procedure 

To adjust the emitter tip position

. 

3. Remove the protective cap on the end of the EASY-Spray column. 

4. With the cable on the bottom, slowly push the tip of the EASY-Spray column into the 

column holder opening until it clicks into place. 

As the EASY-Spray column moves forward into the ion source, the protective cover over 
the emitter retracts to expose the emitter tip. 

5. Connect the cable to the front output heater socket. 

6. Follow the appropriate procedure in 

Examples of LC Connections to the EASY-Spray 

Column

. 

Setting the Column Temperature

Before you begin, turn the temperature control knob to the lowest temperature setting. 

To set the temperature for the EASY-Spray column

Do one of the following: 

• Manually turn the ion source’s temperature control knob. 

• (EASY-nLC 1200 instrument) Use either the Thermo Xcalibur Instrument Setup 

window, or use the EASY-nLC 1200 instrument’s touch screen as follows: 

i.

On the touch-screen’s Home page (top, right corner), press the 

EASY-Spray

 

icon, . 

Note  

You can skip this step after the first time if you have not adjusted the column 

holder’s position. 

CAUTION  High voltage.

 To prevent electric shock, never insert a foreign object, 

especially a conductive part, into the ion source opening. The opening is intended 
only for the emitter positioning tool and the EASY-Spray column. 

Note  

Do not pull on the cable from the EASY-Spray column. Use the plug to connect 

and disconnect the column. 

Summary of Contents for EASY-Spray NG































































Reviews:

No comments