background image

Operating Instructions 

Alpha RES 1000 

 

 

16

1)

 

Follow directions in 7.4.1 to enter Controller mode. 

2)

 

Press the ENTER key. The upper display shows the current controller type and the lower display shows 

“tYP”. 

3)

 

Press the 

Δ

 and 

 keys to select your controller type. 

-

 

L.Ct = limit value pickup (on/off control). 

-

 

oFF = controller off. 

-

 

PLC = pulse length control. 

-

 

PFC = pulse frequency control. 

4)

 

Press the ENTER key to confirm your selection. 

5)

 

Proceed to 7.4.3 step 3, or return to Measurement mode by pressing the 

Δ

 and 

 keys simultaneously 

(escape). 

 
7.4.3

 

Choosing break/make contact relay type 

Note: If the controller type “oFF” is set, the parameters listed in 7.4.4 and 7.4.5 are blanked out.  
This mode lets you determine the relay-state under Non-Alarm condition – dEEN (de-energised) or EN 
(energised). 

1)

 

Follow directions in 7.4.1 to enter Controller mode. 

 

dEEn

   

rEL

HOLD  SETUP

 

2)

 

Press the ENTER key. Scroll until the lower display shows “rEL” and the 

upper display shows the current selection (de-energised = dEEN or 
energised = EN). 

 

 

3)

 

Press the 

Δ

 or 

 keys to choose de-energised or energised  relay state. 

4)

 

Press the ENTER key to confirm your selection. 

5)

 

Continue with Advanced Set-up mode procedures, or return to 

Measurement mode by pressing the 

Δ

  and 

  keys simultaneously 

(escape). 

   

En

 

   

rEL

 

HOLD SETUP

 

 
 
7.4.4

 

Selecting proportional range value Xp 

Note: If the controller type “oFF” or “L.Ct” is set, the parameters listed in 7.4.4 and 7.4.5 are blanked out.  
This mode lets you set a band as a percentage of its full scale value. You can select this range from 10 to 
200%, and the lower display shows “PrP”. 

1)

 

Follow directions in 7.4.1 to enter Controller mode. 

 

100 

  PrP

 

HOLD  SETUP 

2)

 

Press the ENTER key. Scroll until the upper display shows the 

proportional range (a number from 10 to 200%), and the lower display 
shows “PrP”.  

3)

 

Press the 

Δ

 and 

 keys to choose the proportional range value Xp. 

4)

 

Press the ENTER key to confirm your selection. 

5)

 

Proceed to 7.4.5 step 3, or return to Measurement mode by pressing the 

Δ

 and 

 keys simultaneously 

(escape). 

 

Summary of Contents for Alpha RES 1000



































Reviews: